Honda ► CB175K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB175K►
- Honda
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-216-000 / 18291-MN5-650 Sold Each, Order the Quantity you Require
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-216-000 / 18291-MN5-650
Ignition Coil
Ignition Coil 100MM C-C Mounting Points OEM Ref # 30400-306-672 / 30400-306-672
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850177
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Fork Seals
Fork Seals Set/2 31 x 43 x 10
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Plate
Clutch Plate 5 Pieces Required OEM Ref # 22201-302-010 / 22202-ML4-610 / 22202-ML4-611
Steel Clutch Plate
Steel Clutch Plate A OEM Ref # 23311-200-000 Order the Quantity you require
Carb Rebuild Kit
Carb Rebuild Kit. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Fuel Petcock Gasket
Fuel Petcock Gasket, Replaces OEM# 16957-ZE1-812 / 16955-028-004 / 16955-011-010
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-149-000 (700mm), 37260-KB7-010 / 37250-149-000 Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref # 37260-KB7-010 / 37260-438-000 Made in Japan Length is 24" - Confirm this is the length you require before purchasing
Clymer Service Manual
Clymer Service Manual. Clymer motorcycle repair manuals are written specifically for the do-it-yourself enthusiast. From basic maintenance to troubleshooting to complete overhaul, Clymer manuals provide the information you need.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Carb Float & Pin
Carb Float & Pin, Replaces OEM # 16013-116-700 Sold Each, Order the Quantity you Require