Honda ► CB500K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500K►
- Honda
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Spring Set
Clutch Spring Set
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-KY2-000 / 22201-MA6-000 / 22201-MN4-000 / 22201-MT6-601
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Holder Set
Carb Holder Set (Set of 4) - Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM# 16211-323-000 If you require band clamps, these carb holders require our 41-44mm diameter clamps part #15-0684 X8.
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-329-004
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Fuel Petcock Screw and Washer Set
Set of 2 Chrome Plated Fuel Petcock Screws with 2 Fibre Washers. These Screws replace OEM # 93500-06028-0A These screws fasten the fiber washers to the inside of the petcock and attach to the Fuel Tank. It is always a good idea to replace these when installing a New Fuel Petcock on your CB750K (1969-74), CB550K (1974) or CB500K (1971-73). Purchase these with our Petcock #20-8039
Speedometer & Tachometer Crimp Ring Set/2
Speedometer & Tachometer Crimp Ring Set/2 for NIPPON SEIKI gauges. When changing the speedometer or tachometer face plates these rings are often damaged. Get a new set today to have your speedo & tachometer restoration looking perfect! Dimensions: Inner diameter 103.4mm. - Outer diameter 108.2mm.
Trip Meter Knob Rubber Grommet
Day Trip Meter Knob Rubber Grommet. These grommets are often dried out and ripped, get a new one today!
Side Cover Emblem Attachment Nut
Side Cover Emblem Attachment Nut, Replaces OEM# 90315-504-000 Sold Each, Order the Quantity you Require
Fuel Petcock Gasket
Fuel Petcock Gasket / O-Ring, Replaces OEM# 16997-273-006 / 16960-011-000 This is the o-ring that goes between the fuel petcock body and the gas tank. Please ensure you have a stock gas tank prior to ordering
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs!
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Tappet Adjuster Screw & Nut Set
Tappet Adjuster Screw & Nut Set. Each Set includes one Tappet Adjuster Screw and one Nut. Replaces OEM # 90012-426-000 (Adjuster), OEM # 90206-250-000 (Nut). Note: Order the Quantity of Sets your Bike Requires
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402