Honda ► CB750F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750F with universal parts included►
- Honda
Clutch Cover Screw Set
Clutch Cover Screw Set of 10 Screws. Replaces OEM # 93500-06028-0A X7 and 93500-06035-0A X3.
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs and 8 Flange Nuts.
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 15Amp Fuses, Replaces OEM# 38200-MF9-405. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Fork Tube Set
Fork Tube Set/2, Length (580mm or 22 13/16"), 35mm OD. Fits: Honda CB750K (1972) Higher then Frame# 2093730 Only, CB750K (1973-76) NOTE: LENGTH is 22 13/16", one Inch Shorter then Stock Length for these Models below. Fits: Honda CB750K (1977) Higher then Frame# 2707508 Only, CB750K (1978), CB750F (1977-78) Supersport, CB750A (1976-78) Hondamatic Before ordering Please Confirm 22 13/16" is the Length you would like
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Oil Pressure Gauge Assembly ~ Black ~ Joker Machine
Joker Machine Brand ~ Oil Pressure Gauge Assembly. Black Colored Mount Assembly with a Silver Colored Stainless Steel Marshall liquid filled gauge 1 1/2" (38mm) diameter, 0 to 100 PSI. Easily installs on the oil gally port above the points cover in minutes! Features 2 built-in Neoprene rubber o-rings recessed in 2 fittings that have a unique rotating section that enables you to easily position the gauge for perfect rider visibility. Just loosen the billet hex fitting, rotate into position, then tighten. High quality made in the U.S.A
CB750 Engine Stand
CB750 SOHC Engine Rebuild Stand. Make your engine rebuild a lot easier with this engine stand. Very rigid and easily secured to your work bench using holes found in the base of the stand. Powder coated gloss black for a durable finish. High Quality, Made in the USA.
TC Bros. Forward Controls Kit
TC Bros. Brand Bolt-On Forward Controls Kit. Kit includes a pair of forward controls featuring CNC machined, knurled aluminum pegs. The mounting plates are heavy duty powder coated steel and bolt to your front motor mounts. The spacers are TIG welded to the mounting plates. Everything bolts on using the supplied mounting hardware with no frame modifications. Mounting instructions with pictures are included with each kit. This kit makes long trips much more comfortable due to the fact that your legs are extended forward rather than bent. Great for choppers, bobbers, or even stock bikes. High Quality, Made in the USA. Linkage Kit Not Included, We Sell that part #73-1164
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Pilot Indicator Light Cover
Pilot Indicator Light Cover, Replaces OEM# 37600-377-018 This includes the front and rear cover with fastening screws.
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-300-006
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Stock Style Stator
Stock Style Stator, Replaces OEM # 31102-300-045 / 31102-300-035 / 31102-393-025 / 31102-393-005 / 31102-393-015. We had these hard to find stators re-manufactured to keep your CB on the road!
Side Cover Emblem
Side Cover Emblem, Replaces OEM# 87127-392-000 Sold Each, Order the Quantity you Require
Swingarm Dust Seal Cap Set
Swingarm Dust Seal Cap Set of 2, Replaces OEM# 52144-425-831
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Headlight Stay / Headlight Reflector Bolt
Headlight Stay / Headlight Reflector Bolt, Replaces OEM# 90120-425-000. This is the bolt that the headlight reflectors / reflector base attach to, this bolt fastens through the headlight ears. Sold Each, 2 Used Per Bike
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-375-000 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require
Headlight Stay / Headlight Reflector Bolt
Headlight Stay / Headlight Reflector Bolt, Replaces OEM# 90120-377-000 This is the bolt that the headlight reflectors / reflector base attach to, this bolt fastens to the headlight. Sold Each, 2 Used Per Bike
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-425-600 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require
Horn ~ Similar to Stock Style
Horn with Chrome Cover - 12 Volt 3 Amp - 103 Decibel - This is Not identical to the stock type but has a somewhat similar design to the stock type on these bikes.
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Rags”. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - 1 1/2" Pipes Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem Metal Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Peanut Plate Fits 219T Cam Chains
Clip Link
Cam Chain Clip Link Peanut Shape Fits 25H Cam Chains
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BS05MH TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BF05M TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Fits 82RH2015
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Roadhawk Grip Set Chrome Plate Ends With Roadhawk Design 5" Inside Length x 7/8"
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/4" Inside Length x 7/8" 150mm Length
Grips
Sportbike Gel Grip Set Closed End Type 5" Inside Length x 7/8" 135mm Length
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/8" Inside Length x 7/8" 140mm Length
Grips
Foam Grip Set Black Plastic End Inserts 5" Inside Length x 7/8" 130mm Length