Kawasaki ► KZ1000J ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki KZ1000J with universal parts included►
- Kawasaki
Carb Float
Plastic Carb Float OEM Ref # 3H5-14985-00-00 / 16031-1013 / 13250-44080
Starter Brush Set
Starter Brush Set/2 12 x 10 x 5mm 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 10mm x 5mm
Alternator Stator
Alternator Stator OEM Ref # 21003-1040 / 21003-1327
Rectiifer Regulator
Rectifier Regulator, Replaces OEM# 21066-013 / 21066-026 Mounts to the Bottom of the Battery Box (Where the Original Voltage Regulator was Mounted).
Starter Clutch Repair Kit
Starter Clutch Repair Kit
Fork Seals
Fork Seals Set/2 38 X 50 X 8/9.5
Wheel Seal Kit
Front Wheel Seal Kit 2 Seals 22 x 42 x 5 30 x 42 x 7
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Front - Dual
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Rear - Single
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 43082-1007
Brake Pads
Rear Brake Pads Pk/2 OEM Ref # 43082-1008
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Clutch Plate
Clutch Plate 9 Pieces Required OEM Ref # 13088-040 / 13088-1013 / 13088-1051
Clutch Spring Kit
Clutch Spring Kit
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16030-1016
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16030-1016
Intake Carb Holder Set
Intake Carb Holder Set OEM Ref # 16065-1135 4 Pc
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Clutch Cable
Stock Type Clutch Cable, Replaces OEM # 54011-089 / 54011-087 / 54011-1008 / 54011-1018
Drive Chain
Drive Chain 630HT x 96 Average Tensile Strength 11,440Lbs High Tensile Drive Chain With Nickel Plated Side Plates Izumi - Made in Japan
Valve Shim Kit
20 Piece Valve Shim Kit with Plastic Case, 29mm Diameter Valve Shims. Includes 2 of each of the following sizes. 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00, 3.10.
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 11009-1051
Carb Air Filter Duct Rubber Boot
Carb Air Filter Duct Rubber Boot, Replaces OEM# 14073-1048 Sold Each, Order the Quantity you Require (4 Used Per Bike).
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 33040-066 If you require 2 adjusters purchase 2 of this part.