Search ►
Wheel Seal Kit
Rear Wheel Seal Kit 2 Seals 30 x 45 x 9.5 34 x 55 x 9
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Rear - Single
Front Sintered Metal Brake Pad Set
Front Brake Pad Set - Sintered Metal - 67 x 49.5 x 9.5mm. OEM # 45105-410-305 / 45105-461-771 / 45105-461-772 / 45105-438-004 / 45105-438-007 / 45105-438-008
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Clutch Plate
Clutch Plate 5 Pieces Required OEM Ref # 22201-KAE-000 / 22201-KM4-000 / 22201-KA4-711 / 22201-KA4-712 / 22201-KZ3-730 / 22201-MAE-000 / 22201-MAL-600 / 22201-MR7-000 / 22201-MS6-620 / 22201-MV4-000
Steel Clutch Plate
Steel Clutch Plate 7 Used Per Bike OEM Ref # 22321-371-010 / 22321-MG9-000 Order the Quantity you require
Steel Clutch Plate
Steel Clutch Plate 2 Pieces Required Replaces OEM# 22321-KZ3-690
Steel Clutch Plate
Steel Clutch Plate 3 Pieces Required Replaces OEM# 22311-107-000 / 22311-KN4-680
Carb Rebuild Kit
Carb Rebuild Kit for carbs with ROUND CARB BOWLS. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Intake Manifold O-Ring (Pk/2)
Carburetor Intake Manifold O-Rings (Pack of 2), Replaces OEM # 91301-MG9-003 Size 35.5 x 2.6 Order the Quantity you Require.
Cylinder Head Intake Boot O-Rings (Set/4)
Cylinder Head Intake Boot O-Rings, Size 35.5 x 2.6 (Set of 4). Replaces OEM # 91301-MG9-003 These are Used Where the Manifolds Attach to the Cylinder Heads.
Black Driver Back Rest Cover
High Quality Replacement Black Driver Back Rest Cover for the Markland Brand Back Rest. Features a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, made of special cold resistant outdoor 4 way stretch marine vinyl material. This is for the BACK REST COVER, Not the Full back rest. ONLY FITS THE MARKLAND BRAND BACK RESTS
Oil Passage Gasket
Oil Passage Gasket - Replaces OEM# 15128-MG9-000
Sealed Cover Gasket
Sealed Cover Gasket - Replaces OEM# 12391-MG9-000 / 12391-MG9-306 Note: 2 used per bike, order the quantity you require.
Valve Cover Gasket
Valve Cover (Cylinder Head Cover) Gasket - Replaces OEM# 12328-MG9-000 Note: 2 used per bike, order the quantity you require
Transmission Cover Gasket
Transmission Cover Gasket - Replaces OEM# 11391-MG9-000 / 11391-MG9-020 / 11391-MG9-306
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs!
Throttle Cable "A" - Pull Type
Throttle Cable "A" Pull Type, Replaces OEM# 17910-MB9-670 , 17910-371-980 , 17910-371-660.
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-323-000
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-323-000
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-MA2-610
Side Stand Spring
Side Stand Spring, Replaces OEM # 50541-445-010
Left Side Footrest Return Spring
Left Side Footrest Return Spring. This is the Spring that Allows the Left Side Footpeg to be Lowered and Raised. Replaces OEM # 50644-300-670
Spark Advancer Cover Screw Set
Spark Advancer Cover Screw Set of 3, Screw Size 6x25, Replaces OEM # 93700-06025-0A
Clutch Spring Bolt Set
Clutch Spring Bolt Set of 4. Replaces OEM # 92101-06022-0A X4
Right Side Footrest Return Spring
Right Side Footrest Return Spring. This is the Spring that Allows the Right Side Footpeg to be Lowered and Raised. Replaces OEM # 50617-300-670
Jet Needle Set
Jet Needle Set. Replaces OEM # 16012-425-771 Includes Contents show in photo.
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 2.15" Width x 18" x 40 Hole, Overall Actual Width 3.15". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-300-013
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 1.85" Width x 18" x 40 Hole. These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-404-771
Steering Stem Bolt and Washer Set
Steering Stem Bolt and Washer Set. Includes 2 Bolts and 2 Washers. Replaces OEM # 92101-10040-0A X2 (Bolts) and OEM # 94102-10000 X2 (Washers).
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Rear Sprocket ~ 52 Tooth
Rear Sprocket ~ 52 Tooth Replaces OEM# 41201-382-670 Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike. Please note: for the CT125 (1977) - some of these bikes used 56 tooth sprockets.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer, Replaces OEM# 41231-323-020 This is the Rear Wheel - Left Bearing Retainer
Front Brake Cable
Front Brake Cable, Replaces OEM# 45450-428-P00 / 45450-429-P00 / 45450-428-900 / 45450-435-000 / 45450-428-870 / 45450-428-000
Rear Turn Signal Rubber Stem Set
Rear Turn Signal Rubber Stem Set, Replaces OEM# 33604-437-000 / 33604-428-000
Side Cover Emblem
Side Cover Emblem, Replaces OEM# 83606-MG9-000 Sold Each, Order the Quantity you Require
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 139mm Width: 28mm OEM Ref # 43120-942-000
Front Brake Shoes
Front Brake Shoes Pk/2 Diameter: 160mm Width: 20mm OEM Ref # 45151-HC5-006
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Wheel Seal
Wheel Seal 42x62x7 OEM Ref # 91252-958-013 / 91252-958-014 / 91252-958-004
Fuel Tank Emblem Screw Set/4
Fuel Tank Emblem Screw Set/4 (Enough for both fuel tank Emblems), Replaces OEM # 93500-04006-0G
Timing Belt
Timing Belt OEM Ref # 14400-MG9-000 / 14400-MG9-004 Made In Japan
Cam Chain
Silent Cam Chain 412 x110 OEM Ref # 14401-MR4-901 / 14401-HAO-003 / 14401-HAO-771 / 14401-413-014 Made In Japan
Chrome Speedometer & Tachometer Cover Set
Set of Chrome Plated Speedometer & Tachometer Covers. These go over the stock speedo and tach gauges to give them a great chrome look! Diameter at Base of Cover - 103mm Diameter at Top of Covers - 87mm Height of Covers - 37mm Includes a small hole in one of the covers for the tripmeter. Note: Speedo/Tach Not Included, Shown in Photo to illustrate how they look when installed.
Stock Style Speedometer - KPH
Stock Style Speedometer KPH with back illumination, Face dial ranges from 0-240KPH. The ratio of this Speedometer is 100KPH=2330 RPM which is the ratio used on all stock type CB's. Note: The Speedometers slightly changed from year to year, this may not be an exact stock match for your bike but will work great! Housing Size approx 4.6", face 3.9" Check the photo for the design.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Brake Lever
Brake Lever, Replaces OEM# 53175-KA3-681 / 53175-360-700 / 53175-KFO-000
Brake Lever
Brake Lever OEM Ref # 53175-958-0010
Tail Light Assembly
Tail Light Assembly, Replaces OEM# 33701-MA0-003 Includes License Illumination Light