Honda ► CA175 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CA175►
- Honda
Kickstart Rubber
Kickstart Rubber OEM Ref # 28311-329-000 / 95011-51000 / 28311-342-000
Sidecover Damper Rubber A
Rubber Sidecover Damper A, Replaces OEM # 17247-303-000
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Gas Tank Cap
Chrome Cap Gas Tank Cap with Gasket Installed, Replaces OEM# 17620-402-000 , 17620-402-010
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Tail Light Assembly
Tail Light Assembly with Gasket, Replaces OEM# 33700-292-013 / 33700-237-670 / 33700-041-671
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Starter / Horn Button
Starter / Horn Button
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Denso Ignition Contact Points
Contact Points (1pc.) - Replaces OEM # 30202-107-004 / 30202-216-004 / 30202-107-154 These points are for Nippondenso ignitions Only. They are NOT for Hitachi or Kokusan Ignitions. Please check which type you have before ordering. Honda used different ignition systems on some of the same years of bikes.
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-216-000 / 18291-MN5-650 Sold Each, Order the Quantity you Require
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-216-000 / 18291-MN5-650
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
Fuel Petcock
Fuel Petcock, Replaces OEM# 16950-107-000 / 16950-107-005 / 16950-356-005 Single Fuel Output type - Fuel Hose Exits to the Side. Please check the photo, this petcock may not be identical to the OEM type but will work for these models. This petcock has a longer body and the fuel output spigot is located differently then stock for some models.
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Steel Clutch Plate
Steel Clutch Plate A OEM Ref # 23311-200-000 Order the Quantity you require
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Fuel Petcock Gasket
Fuel Petcock Gasket, Replaces OEM# 16957-ZE1-812 / 16955-028-004 / 16955-011-010
Chrome Exhaust Clamp
Chrome Exhaust Clamp, 14 Fin Type, Center to Centre Mounting Hole Diameter 55mm apart. Replaces OEM # 18231-323-000 / 18231-323-010 / 18231-333-010
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-110-000
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Battery Box Rubber "B"
Battery Box Rubber "B", Replaces OEM # 50327-300-000 Sold Each, Order the Quantity you Require
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000