Honda ► CB350F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350F with universal parts included►
- Honda
![Honda CB350F Float Bowl Gasket](/images/parts/100/20-5022.jpg)
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-024, 16010-323-315, 16010-323-004
![Honda CB350F Carb Holder Set](/images/parts/100/48-1471.jpg)
Carb Holder Set
Carb Holder Set (Set of 4) with O-Rings to Seal the Manifolds to the Cylinder Block - Replaces OEM# 16212-333-030 X2 and 16213-333-030 X2
![Honda CB350F Float Needle & Seat](/images/parts/100/48-1510.jpg)
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-329-004
![Honda CB350F Carb Rebuild Kit](/images/parts/100/48-1903.jpg)
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
![Honda CB350F Carb Diaphragm Rubber](/images/parts/100/48-1985.jpg)
Carb Diaphragm Rubber
Carburetor Top Diaphragm Rubber. Outer dimension 72mm - Inner dimension 25mm. Replaces the diaphragm rubber on Honda OEM# 16022-287-004 / 16022-287-014 / 16022-287-024. Note: When installing be sure to line up the rubber tab on the diaphragm so the slide is in it's proper orientation. Sold Each, order the quantity you require.
![Honda CB350F Float Bowl Drain Screw](/images/parts/100/48-5041.jpg)
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
![Honda CB350F Carburetor Screw Kit](/images/parts/100/49-0775.jpg)
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 16X- 4x12 Screws w Lock Washers 8X - 5x16 Screws w Lock Washers 2X - 6x14 Screws w Lock Washers
![Honda CB350F Carb Bolt Kit](/images/parts/100/73-1046.jpg)
Carb Bolt Kit
Carburetor Bolt and Washer 40 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
![Honda CB350F Gear Clamp 40-60mm.](/images/parts/100/15-0670.jpg)
Gear Clamp 40-60mm.
Universal Gear Clamp for Carb Holders or Air Boxes. 9mm Wide. Adjusts with a screwdriver. Fits: Diameters 40-60mm (With a width of 9mm)
![Honda CB350F Universal Band Clamp](/images/parts/100/15-0672.jpg)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 53-56mm. (1.92" - 2.16")
![Honda CB350F Universal Band Clamp](/images/parts/100/15-0673.jpg)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 60mm-65mm or 2.36" to 2.56"
![Honda CB350F Universal Band Clamp](/images/parts/100/15-0684.jpg)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 41-44mm. (1.53" - 1.69")
![Honda CB350F Universal Band Clamp](/images/parts/100/15-0685.jpg)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 46-49mm. (1.77" - 1.92")
![Honda CB350F Universal Band Clamp](/images/parts/100/15-0686.jpg)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 66-69mm. (2.48" - 2.63")
![Honda CB350F Universal Band Clamp](/images/parts/100/15-0687.jpg)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 69-72mm. (2.67" - 2.87")
![Honda CB350F Band Clamp 45-47mm.](/images/parts/100/15-0688.jpg)
Band Clamp 45-47mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 45-47mm.
![Honda CB350F Band Clamp 50-52mm.](/images/parts/100/15-0689.jpg)
Band Clamp 50-52mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 50-52mm.
![Honda CB350F Band Clamp 58-60mm.](/images/parts/100/15-0690.jpg)
Band Clamp 58-60mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 58-60mm.
![Honda CB350F Band Clamp 43-49mm](/images/parts/100/15-0691.jpg)
Band Clamp 43-49mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 43-49mm. (1.69"-1.93") Diameters
![Honda CB350F Band Clamp 67mm-73mm](/images/parts/100/15-0693.jpg)
Band Clamp 67mm-73mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 67-73mm. (2.64"-2.87") Diameters
![Honda CB350F Band Clamp 73mm-79mm](/images/parts/100/15-0694.jpg)
Band Clamp 73mm-79mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 73-79mm. (2.87"-3.11") Diameters
![Honda CB350F Band Clamp 79-85mm](/images/parts/100/15-0695.jpg)
Band Clamp 79-85mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifold to Filter Joints and all purpose uses except carb holders. Fits: 79-85mm. (3.11"-3.35") Diameters
![Honda CB350F Band Clamp 85-91mm](/images/parts/100/15-0696.jpg)
Band Clamp 85-91mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 85-91mm. (3.35"-3.58") Diameters
![Honda CB350F Band Clamp 91-97mm](/images/parts/100/15-0697.jpg)
Band Clamp 91-97mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 91-97mm (3.58"-3.82") Diameters
![Honda CB350F Band Clamp 97mm-103mm](/images/parts/100/15-0698.jpg)
Band Clamp 97mm-103mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 97-103mm (3.82"-4.00") Diameters
![Honda CB350F Band Clamp 103mm-109mm](/images/parts/100/15-0699.jpg)
Band Clamp 103mm-109mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 103-109mm (4.00"-4.29") Diameters
![Honda CB350F Band Clamp 109mm-115mm](/images/parts/100/15-0700.jpg)
Band Clamp 109mm-115mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 109-115mm (4.29"-4.53") Diameters
![Honda CB350F Band Clamp 115mm-121mm](/images/parts/100/15-0701.jpg)
Band Clamp 115mm-121mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 115-121mm. (4.53"-4.76") Diameters
![Honda CB350F Band Clamp 121mm-127mm](/images/parts/100/15-0702.jpg)
Band Clamp 121mm-127mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 121-127mm. (4.76"-5.00") Diameters
![Honda CB350F Band Clamp 37-43mm](/images/parts/100/15-0703.jpg)
Band Clamp 37-43mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifold to Filter Joints and all purpose uses except carb holders. Fits: 37-43mm. (1.45"-1.69") Diameters
![Honda CB350F Band Clamp 78-80mm](/images/parts/100/15-2031.jpg)
Band Clamp 78-80mm
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 78-80mm.
![Honda CB350F Carb Float Level Gauge](/images/parts/100/35-0043.jpg)
Carb Float Level Gauge
Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors. Adjustable Width: 16-78mm and Adjustable Height 0-40mm
![Honda CB350F Hose Remover Pliers](/images/parts/100/35-0049.jpg)
Hose Remover Pliers
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
![Honda CB350F 382pc O-Rings Kit with Plastic Case](/images/parts/100/35-0066.jpg)
382pc O-Rings Kit with Plastic Case
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm 10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm 10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm 10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm 10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm 10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm 10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
![Honda CB350F 419pc O-Rings Kit with Plastic Case](/images/parts/100/35-0067.jpg)
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
![Honda CB350F Carburetor Adjusting Tool](/images/parts/100/35-0084.jpg)
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
![Honda CB350F Carburetor Synchronizer Vacuum Gauge ~ 2,3,4 Cylinders](/images/parts/100/35-0085.jpg)
Carburetor Synchronizer Vacuum Gauge ~ 2,3,4 Cylinders
Carburetor and throttle body synchronizer kit for bikes with 2, 3 or 4 Cylinders. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2, 3 or 4 cylinders. Includes 4 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
![Honda CB350F Carb Cleaning Tool Set](/images/parts/100/35-9110.jpg)
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from 0.45mm to 1.5mm.
![Honda CB350F Fluid Hose Clamp](/images/parts/100/35-9117.jpg)
Fluid Hose Clamp
Fluid Hose Clamp, all steel construction with adjustable locking collar. Completely or partially closes flexible brake, fuel, and vacuum fluid lines.
![Honda CB350F Portable Auxiliary Fuel Tank Tool](/images/parts/100/35-9120.jpg)
Portable Auxiliary Fuel Tank Tool
Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed. Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
![Honda CB350F Carb Cleaning Tool Set](/images/parts/100/35-9125.jpg)
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
![Honda CB350F Carburetor Synchronizer Vacuum Gauge ~ 2 Carb Synchronizer](/images/parts/100/37-0003.jpg)
Carburetor Synchronizer Vacuum Gauge ~ 2 Carb Synchronizer
Carburetor and throttle body synchronizer kit for bikes with 2 Carbs. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2 carbs. Includes 2 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.