Honda ► CB350K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB350K with universal parts included that match “honda sl125”►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 135mm Length. Replaces OEM #' 53165-342-670 / 53166-342-670
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670
Brake Lever
Brake Lever OEM Ref # 53175-402-700 / 53170-216-670 / 53175-286-000 / 53170-286-670 / 53170-329-010 / 53170-369-700 / 53175-369-700
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Kickstart Rubber
Kickstart Rubber OEM Ref # 28311-329-000 / 95011-51000 / 28311-342-000
Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Shock Absorber Set ~ Stock Design
Stock Type Designed Shock Absorber Set - Chrome Body and Cover with Chrome Springs. These are modelled after the original stock shocks. Replaces OEM# 52400-455-670XW / 52400-390-681XW / 52400-292-670XW / 52400-323-010XW
The original OEM shocks came with 3 position spring preload adjustments however we have upgraded these to 5 spring preload adjustments so you can better fine tune these shocks! 321mm (12.6") Center of Eye to Clevis.
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover - Replaces OEM# 87126-344-671 These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87125-344-671 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Carb Diaphragm Rubber
Carburetor Top Diaphragm Rubber. Outer dimension 72mm - Inner dimension 25mm. Replaces the diaphragm rubber on Honda OEM# 16022-287-004 / 16022-287-014 / 16022-287-024. Note: When installing be sure to line up the rubber tab on the diaphragm so the slide is in it's proper orientation. Sold Each, order the quantity you require.
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your original seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-17000 / 40543-286-000. If you require 2 adjusters purchase 2 of this part.
Front Brake Cable
Front Brake Cable, Replaces OEM# 45450-329-010