Honda ► CB360G ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB360G►
- Honda
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Spring Set
Clutch Spring Set
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Carb Rebuild Kit
Carb Rebuild Kit. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Holder Set
Carb Holder Set (Set of 2 with Gaskets). Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM #'s 16211-369-000 X2 and 16229-369-000 X2 NOTE-If you require band clamps, these carb holders require our 46-49mm diameter clamps part #15-0685 X2.
Carb Intake Manifold
Carb Intake Manifold - Replaces OEM# 16211-369-000 NOTE: This is for One Holder, Order the Quantity you Require. If you require band clamps, these carb holders require our clamps part #15-0685
Carb Slide Diaphragm Rubber Set
Carb Slide Diaphragm Rubbers Set - Includes 2 Diaphragms (Rubber Portion Only as Shown) and 2 O-Rings. Replaces Rubber Portion on OEM# 16022-369-004
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-369-004
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Tappet Adjuster Screw & Nut Set
Tappet Adjuster Screw & Nut Set. Each Set includes one Tappet Adjuster Screw and one Nut. Replaces OEM # 90012-426-000 (Adjuster), OEM # 90206-250-000 (Nut). Note: Order the Quantity of Sets your Bike Requires
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-149-000 (700mm), 37260-KB7-010 / 37250-149-000 Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref # 37260-KB7-010 / 37260-438-000 Made in Japan Length is 24" - Confirm this is the length you require before purchasing
Front Brake Hose "B"
Front Brake Hose "B", Connects Front Brake Master Cylinder to 3-Way Joint. Replaces OEM # 45126-300-003
Brake Hose Rubber Grommet
Brake Hose Rubber Grommet, This is the Rubber Grommet that Attaches to the Brake Hose. Replaces OEM # 45146-300-000
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Front Stop Switch Sub Harness
Front Stop/Brake Switch Sub Harness, Replaces OEM # 35345-319-000
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Front Wheel Spoke Set
Front Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Front Type Rims Only
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Fork Dust Boot Set
Fork Seal Dust Boots (Set/2). 33mm Size, Replaces OEM # 91254-413-881
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Master Cylinder Damper Set
Master Cylinder Damper Set. Includes Brake Master Cylinder Rubber Damper, Plate and Washer. This Set is often missing and is used to reduce vibration to the master cylinder lever.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Throttle Adjusting Spring
Throttle Adjusting Spring, Replaces OEM # 53191-300-000
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Valve Guide Clip
Valve Guide Clip, Replaces OEM # 12211-250-310 Sold Each, Order the Quantity you Require
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Cap (Set/2). These Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-362-000 X2.
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000