Honda ► CB400F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB400F►
- Honda
Round Pod Air Filter ~ Black/Red
39mm Round Pod Air Filter ~ Black Body with Red Foam Filter - Circular style with Black end cap. Provides for greater air flow, especially when using an aftermarket exhaust and has improved flow characteristics compared to the plain wire type mesh Pod filters. Filter is supplied dry but washable filtration material may be oiled for improved dust filtration.
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Oil Filter O-Ring Set
Oil Filter O-Ring Set Fits Oil Filter - 15410-426-005 / 15410-426-010
Oil Filter Spring
Oil Filter Spring, Replaces OEM # 15415-300-000
Foam Round Pod Air Filter
39mm Round Foam Pod Air Filter With Chrome End Caps and Rubber Mouth - Circular style.
Stock Type Air Filter
Stock Type Air Filter - OEM Ref # 17210-333-610
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Oil Filter Bolt
Oil Filter Bolt OEM Ref # 15420-300-020
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
CB Black Mirror - Original Type (Left Side)
Gloss Black CB Style Left Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
CB Black Mirror - Original Type (Right Side)
Gloss Black CB Style Right Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-028-000 / 18291-028-306 Sold Each, Order the Quantity you Require
Exhaust Headpipe Gaskets - (Pk/10)
Exhaust Port Gaskets (Pk./10) - OEM Ref. # 18291-028-000 / 18291-028-306
Bar Switch Assembly ~ Left (Clutch) Side
European Version (8 Wire) Bar Switch Assembly ~ Left (Clutch) Side - Black. Please be sure to double check your harness requires this 8 wire type switch Before ordering. Replaces OEM # 35200-377-671 Note: Wiring to be run Inside the handlebar.
Mounting Rubber
Mounting Rubber, Replaces OEM # 17245-107-010
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB400F (1975-77) Supersport Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Athena Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850401/1
Overhaul Gasket Set
Overhaul Engine Gasket Set
Valve Tappet Cover Gasket Set/8
Valve Tappet Cover Gaskets Set/8. These are made for the stock type Valve Tappet Covers. These replace OEM # 91302-001-020 Note:These will only work on OEM type Tappet covers
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-024, 16010-323-315, 16010-323-004
Carb Float
Carb Float with Pin, Replaces OEM # 16013-333-004 Note: 4 Carb Floats Used Per Bike, Order Quantity you Require
Float Bowl Gasket
Float Bowl Gasket
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Stock Style Stator
Stock Style Stator, Replaces OEM # 31102-333-004
Condenser
Condenser OEM Ref # 30250-333-004
Fork Seals
Fork Seals Set/2 33 X 46 X 11
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 52108-457-300 Note: These Replace the factory plastic OEM Type Bushings.
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Cotter Valve / Valve Keeper
Cotter Valve / Valve Keeper, Replaces OEM# 14781-107-003 / 14781-107-020. 2 Used For Each Valve Spring. Sold Each, Order the Quantity you Require
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 159mm Width: 30mm OEM Ref # 43120-KG4-006
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-390-006A
Tachometer Cable Clamp
Chrome Tachometer Cable Clamp (Holder). Replace that Old Rusted, Worn Out Clamp with a Brand New Great Looking Chrome Tach Cable Clamp. Replaces OEM # 50462-323-010
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Clutch Lever Return Spring
Clutch Lever Return Spring. This is the Spring Located Behind the Clutch Cover. Replaces OEM # 22815-300-000
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000