Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included that match “honda sl125”►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 95011-14100 / 95011-14200
Gas Tank Cap
Chrome Cap Gas Tank Cap with Gasket Installed, Replaces OEM# 17620-402-000 , 17620-402-010
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Clutch Lever Perch
Clutch Lever Perch, Replaces OEM# 53172-310-010 / 53172-110-000 / 53172-310-000 Includes a 10mm Mirror Mount, for 7/8" handlebars
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Overhaul Gasket Set
Engine Overhaul Gasket Set Fits: Honda CB450K (1965-74) - 5 Speed Models Only, CL450K (1968-74), CB500T (1975-76)
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-110-000
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Passenger Rear Footpeg Pin & Cotter Pin Set
Passenger Rear Footpeg Pin & Cotter Pin Set. Set Includes 2 Footpeg Pins and 2 Cotter Pins. Replaces OEM # 95015-83000
Carb Float
Carb Float with Pin, Replaces OEM # 16013-283-004 Note: Sold Each, Order Quantity of Floats your Bike Requires.
Clutch Plate
Clutch Plate 7 Piece Required OEM Ref # 22201-283-000 / 22201-MA7-000
Cam Chain 219FTSS x 128
Cam Chain 219FTSS x 128 D.I.D (Daido) Takes 01-8802 Rivet Link Pitch: .3061" Side Plate: Steeped Parallel Plate Average Tensile Strength: 1896lbs OEM Ref # 14401-283-003 / 94500-02128
Cam Chain
Cam Chain 219T x 128 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-283-003 / 94500-02128
Honda Handlebar Pad
Honda Handlebar Pad Protect your chest and spruce up the look of your bike with a brand new handlebar pad. These will fit to 1/8" and 7/8" bars.
Honda Tin Sign
Honda Tin Sign Spruce up your garage or man cave with this 12" by 12" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo Flag
Honda Logo Flag - Features the classic Honda logo, measures 36" by 23" and includes metal stud holes in each corner for easy mounting. Will look great in any garage or shop!
Honda Beanie Hat / Toque
Honda Beanie Hat / Toque. This black beanie features the classic Honda Logo on both sides. This hat is one size fits all but does fit quite large.
Honda Garage - Tin Sign
Honda Garage with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Leather Honda Logo Keychain
High Quality Leather Honda Logo Keychain with Second Logo at the Base.
Honda Riding Bandana / Scarf
Honda (The Power of Dreams) Riding Bandana / Scarf. This lightweight breathable bandana is perfect for riding on your bike and keeping debris away from your mouth and face.
Honda Gray Trucker Hat
Honda Gray Trucker Hat With Quality Sewn on Patch Snap On Adjustable Back
Honda Wing Floor Mat
Honda Wing Floor Mat. This mat makes a great addition to any garage/shop or mancave! Measures 15.75" x 24"
Honda Logo (White Logo) - Tin Sign
Honda Logo (White Logo) with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo (Red Background) - Tin Sign
Honda Logo (Red Background) with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo (Black Background) - Tin Sign
Honda Logo (Black Background) with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo Keychain with Fibre Background
Honda Logo Keychain with Carbon Fibre Looking Background
Honda Logo Keychain with Carbon Background
Honda Logo Keychain with Carbon Pattern Background