Honda ► CB450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB450K with universal parts included that match “honda sl125”►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 95011-14100 / 95011-14200
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Stock Type Mirror Set
Stock Type Mirror Set/2, Replaces OEM# 88110-329-730 / 88110-074-000 / 88120-329-730 / 88120-074-000 Chrome Mirrors, 8" Stem Length
Throttle Sleeeve
Throttle Sleeve
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Gear Change Rubber
Gear Change Rubber OEM Ref # 95011-400-000
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Overhaul Gasket Set
Engine Overhaul Gasket Set Fits: Honda CB450K (1965-74) - 5 Speed Models Only, CL450K (1968-74), CB500T (1975-76)
Fork Internal Circlip Set
Fork Internal Circlip (50mm) Set/2, Replaces OEM # 94521-50000 Fits: Honda CB750K (1971), CB750K (1972) Frame Numbers Lower then #2093731 Only
Shock Absorber Set ~ Stock Design
Stock Type Designed Shock Absorber Set - Chrome Body and Cover with Chrome Springs. These are modelled after the original stock shocks. Replaces OEM# 52400-455-670XW / 52400-390-681XW / 52400-292-670XW / 52400-323-010XW
The original OEM shocks came with 3 position spring preload adjustments however we have upgraded these to 5 spring preload adjustments so you can better fine tune these shocks! 321mm (12.6") Center of Eye to Clevis.
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
CB450K 1969-72 Gas Tank Stripe Decals ~ Gold Stripes
Honda CB450K (1969-72) Gold Gas Tank Stripe Decals (Stickers). These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
CB450K 1969-72 Gas Tank Stripe Decals ~ Black Stripes
Honda CB450K (1969-72) Black Gas Tank Stripe Decals (Stickers). These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM # 17613-292-000
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-292-003 / 30203-292-154
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Turn Signal Lamp
Turn Signal Lamp - Front or Rear 2 Wire - 12 Volt Stem *Our Part Number 11-2167*
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17525-300-000
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Cylinder Head Gasket
Cylinder Head Gasket, Replaces OEM# 12909-428-003 / 12909-283-000 / 12909-333-000.
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Front Brake Pipe "B"
Front Brake Pipe "B" - Replaces OEM# 45128-300-010 Aprox 7 7/8" Total Length.
Tongued Front Disk Rotor Washer & Nut Set
Front Disk Rotor A8 Tongued Washer & Nut Set. This Set Includes 3 Washers and 6 Nuts. Replaces OEM # 94108-18000 (Tongued Washers) and OEM # 94001-08000-0S (Nuts). These Washers are used for Locking the Nuts that Hold the Front Disc to the Hub.
Bar Switch Assembly - Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side. Replaces OEM # 35300-319-670
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Brake Hose Rubber Grommet
Brake Hose Rubber Grommet, This is the Rubber Grommet that Attaches to the Brake Hose. Replaces OEM # 45146-300-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Front Brake Hose "A"
Front Brake Hose "A", Attaches 3-Way Joint to Front Brake Pipe. Replaces OEM # 45125-300-003
Bronze Thrust Bushing Set/2
Bronze Thrust Bushing Set/2. Replace the cheaply made, worn-out factory swingarm bushings with a 2-piece set of brand-new bronze thrust bushings. Replaces OEM # 52109-283-300
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-18000 / 40543-390-000 / 40532-283-010. If you require 2 adjusters purchase 2 of this part.
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685
Front Brake Hose Guide
Front Brake Hose Guide, Replaces OEM # 45129-300-000
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Master Cylinder Damper Set
Master Cylinder Damper Set. Includes Brake Master Cylinder Rubber Damper, Plate and Washer. This Set is often missing and is used to reduce vibration to the master cylinder lever.
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require