Honda ► CB500K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB500K with universal parts included that match “honda sl125”►
- Honda
Pilot Lamp Indicator Panel Dash Light Harness
Pilot Lamp Indicator Panel Dash Light Harness, Replaces OEM# 37581-323-000 / 37581-374-670 Comes complete with bulbs.
Alternator Cover Gasket
Alternator Cover Gasket - OEM Ref. # 11691-323-306
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-323-000
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-323-000
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Contact Point
Contact Point - Right Side OEM Ref # 30203-300-005 / 30203-300-154
Contact Point
Contact Point - Left Side OEM Ref # 30204-300-005 / 30204-300-154
Condenser
Condenser OEM Ref # 30250-300-154 / 30250-300-005
Rear Turn Signal Mount & Collar Set
Rear Turn Signal Mount, Collar and Rubber Set. Includes both Left and Right Sides. These are needed when installing the Rear signals. Replaces OEM # 33605-323-670 (Left Side) & 33606-074-010 (Right Side).
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Headlight Case Collar
Headlight Case Collar, Replaces OEM# 61302-300-000 This is the collar that goes in each side of the stock headlight case. Sold Each, order the quantity you require
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set. This Set is Used to Mount the Tail Light Bracket. This 12pc Set Includes 4pc Tail Light Setting Bolts, 4pc Tail Light Setting Washer and 4pc Rubber Fender Cushion.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.