Honda ► CB500K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB500K►
- Honda
Tail Light Bracket
Chrome Tail Light Bracket, Replaces OEM # 84701-341-670 / 84701-371-980
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Ignition Coil Bracket Set
Ignition Coil Bracket Set. Replaces OEM# 30511-300-000 Features a high grade polished finish and includes coil mounting hardware.
Headlight Case Collar
Headlight Case Collar, Replaces OEM# 61302-300-000 This is the collar that goes in each side of the stock headlight case. Sold Each, order the quantity you require
Headlight Setting Collar
Headlight Setting Collar, Replaces OEM# 61304-292-000 Sold Each, order the quantity you require
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek 3 Ohm coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.
Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.
Dynatek Dyna 2000 Digital Perfomance Ignition
Dynatek Dyna 2000 Digital Performance CDI Ignition. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek.
Headlamp Rim & Retainer
Headlamp Rim & Retainer Assembly - OEM Ref. # 33101-404-671 / 33101-300-673 / 33101-405-671 / 33100-371-980
Headlamp Rim
Headlamp Rim - Chrome - Replaces OEM # 33101-300-673 / 33101-405-671
Starter Solenoid Relay
Starter Solenoid Relay, Replaces OEM# 35850-371-670 / 35850-306/670 / 35850-HA7-670
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Turn Signal Lamp
Turn Signal Lamp - Front or Rear 2 Wire - 12 Volt Stem *Our Part Number 11-2167*
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Pilot Lamp Indicator Panel Dash Light Harness
Pilot Lamp Indicator Panel Dash Light Harness, Replaces OEM# 37581-323-000 / 37581-374-670 Comes complete with bulbs.
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Stock Type Front Reflector Rubber Base
Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670
Rear Signal Lamp Stay
Rear Signal Lamp Stay - Chrome Honda Rear - OEM Ref # 33607-323-670 65mm Long.
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Starter / Horn Button
Starter / Horn Button
Ignition Switch Assembly
Ignition Switch Assembly Square End Plug Type - 4 Prong OEM Ref # 35100-341-700 / 35100-374-007 / 35100-369-740 Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch.
Bar Switch Assembly ~ Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side - Black. Replaces OEM # 35300-323-671
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Contact Point
Contact Point - Right Side OEM Ref # 30203-300-005 / 30203-300-154
Contact Point
Contact Point - Left Side OEM Ref # 30204-300-005 / 30204-300-154
Alternator Cover Gasket
Alternator Cover Gasket - OEM Ref. # 11691-323-306
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 68mm Length, 94mm Width, 26mm Height, Hole Distance 80.0mm Center to Center. High quality Part. Note: May require a custom mounting job. Works great if attached with one bolt and nut where the safety starter switch was originally located (can bypass that switch).
Condenser
Condenser OEM Ref # 30250-300-154 / 30250-300-005
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set. This Set is Used to Mount the Tail Light Bracket. This 12pc Set Includes 4pc Tail Light Setting Bolts, 4pc Tail Light Setting Washer and 4pc Rubber Fender Cushion.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Tail Light Cable Set
Tail Light/Brake Light Cable Set of 3. Replaces OEM # 33711-323-000 (Tail Light Sub Cable), OEM # 33712-300-003 (Taillight Ground Cable) and OEM # 33713-323-000 (Stop Light Sub Cable).
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Front Stop Switch Sub Harness
Front Stop/Brake Switch Sub Harness, Replaces OEM # 35345-319-000
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-323-000
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-323-000