Honda ► CB500K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB500K with universal parts included►
- Honda
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Master Cylinder Damper Set
Master Cylinder Damper Set. Includes Brake Master Cylinder Rubber Damper, Plate and Washer. This Set is often missing and is used to reduce vibration to the master cylinder lever.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Throttle Adjusting Spring
Throttle Adjusting Spring, Replaces OEM # 53191-300-000
Valve Stem Seal
Valve Stem Seal. Replaces OEM # 12209-333-005 / 12209-333-005 Sold Each - Order the Quantity you Require
Bronze Thrust Bushing Set/2
Bronze Thrust Bushing Set/2. Replace the cheaply made, worn-out factory swingarm bushings with a 2-piece set of brand-new bronze thrust bushings. Replaces OEM # 52109-283-300
Carb Float Setting Tool
Carb Float Setting Tool. Use this tool to help set your floats with ease! This pre-set float setting gauge is for the models/years below only. Fits: Honda CB500K (1971-73), CB550K (1974-76), CB550F (1975-77) Supersport
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-300-010
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Wire Harness
Main Wire Harness Loom - OEM Ref # 32100-323-040 NOTE: These fit model years and types listed, other years and bikes use a different OEM part number (there is a difference!).
Wire Harness
Main Wire Harness Loom - OEM Ref # 32100-323-020 NOTE: These fit model years and type listed, other years and bikes use a different OEM part number (there is a difference!).
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Seat Hinge Pin
Seat Hinge Pin, Replaces OEM # 77103-313-000 Note: 2 Used Per Bike, Order the Quantity you Require
Crank Seal
Crank Seal - 30 x 42 x 8 - Replaces OEM # 91201-300-003 Note: Please Reference the OEM Number and Seal size above to make sure this is the Crank Seal you Require. Some models use 2 Different Crank Seals.
Kickstart Oil Seal
Kickstart Oil Seal - 18 x 29 x 7 - Replaces OEM # 91204-286-003
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 4 - Replaces OEM # 91256-096-651
Intake Valve
Intake Valve - Replaces OEM # 14711-107-020 Made in Japan
Exhaust Valve
Exhaust Valve - Replaces OEM # 14721-323-005 / 14721-324-010 / 14721-324-000 / 14721-107-020 Made in Japan
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Fork Internal Circlip Set
Fork Internal Circlip (48mm) Set/2, Replaces OEM # 94521-48000
Tongued Front Disk Rotor Washer & Nut Set
Front Disk Rotor A8 Tongued Washer & Nut Set. This Set Includes 3 Washers and 6 Nuts. Replaces OEM # 94108-18000 (Tongued Washers) and OEM # 94001-08000-0S (Nuts). These Washers are used for Locking the Nuts that Hold the Front Disc to the Hub.
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Front Stock Type Rim
Chrome Front Stock Type Rim, 1.85" Width x 19" x 40 Hole, Overall Actual Width 2.75". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 44701-405-771
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 1.85" Width x 18" x 40 Hole. These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-404-771
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB550K (1974-76), CB500K (1971-73) Seat This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Swing Arm Felt (Set/2)
Swing Arm Felt (Set/2), Replaces OEM # 52145-283-000
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Headlight Bucket Case
Black Headlight Bucket / Case, Stock Design - Replaces OEM # 61301-300-020B
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)
TC Bros. Forward Controls Kit
TC Bros. Brand Bolt-On Forward Controls Kit. Kit includes a pair of forward controls featuring CNC machined aluminum pegs. The brackets are TIG welded and powder coated steel. Everything bolts right on using supplied mounting hardware and with no frame modifications. Mounting instructions with pictures are included in every kit. This is an easy mod to do to your bike and makes long trips much more comfortable due to the fact that your legs are extended forward rather than bent. Great for choppers, bobbers, or even stock bikes. High Quality, Made in the USA. Linkage Kit Not Included
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer, Replaces OEM# 41231-323-020 This is the Rear Wheel - Left Bearing Retainer
Side Cover Emblem
Side Cover Emblem with Attachment Clips, Replaces OEM# 87124-323-000 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Piston Ring Set (Standard Size)
Standard Size Piston Ring Set Replaces OEM# 13011-323-014 / 13011-323-013 Fits: Honda CB500K (1971-73) Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Piston Kit (Standard Size)
Standard Size (56mm) Piston with Piston Rings, Piston Pin and Piston Pin Clips (pr.) Replaces OEM# 13101-323-000 (Piston), 13011-323-014 / 13011-323-013 (Piston Rings), 94601-15000 (Clip), 13111-440-000 / 13111-286-000 (Pin) Fits: Honda CB500K (1971-73) Note: This Kit includes piston, piston rings, piston pin and clips to rebuild one piston. 4 Kits are needed to rebuild all pistons.
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.