Honda ► CB550F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB550F with universal parts included that match “honda sl125”►
- Honda
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Turn Signal Lamp
Turn Signal Lamp 1-Wire - Rear OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM# 17613-286-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 5 1/8" Offset 1 3/8"
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Kickstart Oil Seal
Kickstart Oil Seal - 18 x 29 x 7 - Replaces OEM # 91204-286-003
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 4 - Replaces OEM # 91256-096-651
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Horn ~ Similar to Stock Style
Horn with Chrome Cover - 12 Volt 3 Amp - 103 Decibel - This is Not identical to the stock type but has a somewhat similar design to the stock type on these bikes.
High Performance Kibblewhite Black Diamond Exhaust Valve
High Performance Kibblewhite Black Diamond Exhaust Valve. Replaces OEM# 14721-323-005. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. All Black Diamond Stainless steel valves are impregnated by a special German process to a depth of .002, with a surface build up of .0002. This Black Diamond process improves wear properties, reduces friction, and provides resistance to corrosion and wear that is superior to chrome and nickel electrolysis plating. Each valve is designed using Finite Element Analysis software, and profiles are tested on our computerized flow bench. Black Diamond Valves are lightweight, strong, one piece forgings with profiles that provide excellent flow characteristics. Sold Each, Order the Quantity you Require
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35200-374-671
Cylinder Head Gasket
Cylinder Head Gasket - OEM Ref.# 12251-374-306
Cylinder Head Cover Gasket
Cylinder Head Cover Gasket - OEM Ref.# 12391-323-000
Alternator Cover Gasket
Alternator Cover Gasket - OEM Ref. # 11691-323-306
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs!
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-323-000
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-323-000
Clutch Spring Bolt Set
Clutch Spring Bolt Set of 4. Replaces OEM # 92101-06022-0A X4
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 1.85" Width x 18" x 40 Hole. These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-404-771
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs, 8 Washers and 8 Nuts.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer, Replaces OEM# 41231-323-020 This is the Rear Wheel - Left Bearing Retainer
Chrome Speedometer & Tachometer Cover Set
Set of Chrome Plated Speedometer & Tachometer Covers. These go over the stock speedo and tach gauges to give them a great chrome look! Diameter at Base of Cover - 103mm Diameter at Top of Covers - 87mm Height of Covers - 37mm Includes a small hole in one of the covers for the tripmeter. Note: Speedo/Tach Not Included, Shown in Photo to illustrate how they look when installed.
Stock Style Speedometer - KPH
Stock Style Speedometer KPH with back illumination, Face dial ranges from 0-240KPH. The ratio of this Speedometer is 100KPH=2330 RPM which is the ratio used on all stock type CB's. Note: The Speedometers slightly changed from year to year, this may not be an exact stock match for your bike but will work great! Housing Size approx 4.6", face 3.9" Check the photo for the design.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Contact Point
Contact Point - Right Side OEM Ref # 30203-300-005 / 30203-300-154
Contact Point
Contact Point - Left Side OEM Ref # 30204-300-005 / 30204-300-154
Athena Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product #P400210850529
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-300-010
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Rear Brake Shoe Spring Set/2
Rear Brake Shoe Spring Set of 2. Replaces OEM # 43151-346-000
Brake Lever
Brake Lever OEM Ref # 53175-369-003 / 53175-300-020 / 53170-333-000
Brake Lever ~ GP Style
Brake Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53175-369-003
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Custom Type Black Fork Caps (Set/2) ~ Joker Machine
Joker Machine Brand ~ Custom Black Fork Cap Set of 2 with O-Rings. Replaces OEM # 90123-300-000 High quality CNC machined from billet aluminum, much lighter then the stock type. Gives your bike a great custom look. Made in the U.S.A.
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Headlight Case Collar
Headlight Case Collar, Replaces OEM# 61302-300-000 This is the collar that goes in each side of the stock headlight case. Sold Each, order the quantity you require
Crank Seal
Crank Seal - 30 x 42 x 8 - Replaces OEM # 91201-300-003 Note: Please Reference the OEM Number and Seal size above to make sure this is the Crank Seal you Require. Some models use 2 Different Crank Seals.
Front Brake Master Cylinder Rebuild Kit
Front Brake Master Cylinder Rebuild Kit - OEM Ref # 45530-404-315 Made in Japan
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!