Honda ► CB550K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB550K that match “honda sl125”►
- Honda
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Front Brake Master Cylinder Repair Kit
Front Brake Master Cylinder Repair Kit OEM Ref # 45530-377-305
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Turn Signal Replacement Lens ~ Smoked
Turn Signal Replacement Lens - Smoked - Front or Rear OEM Ref # 4H7-83312-00
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Throttle Cable - Pull
Throttle Cable "Pull Type" - OEM Ref. # 17910-341-000 - End to End Length 40"
Cam Chain
219H x 88 Cam Chain - OEM Ref. # 14401-362-003 / 14401-323-003 The latest high strength cam chain from D.I.D. Japan. This is a continuous chain.
Fuse Box Assembly
Fuse Box Assembly Complete with 5 Fuses and Fuse Box Cover, Replaces OEM # 38200-377-305
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33406-377-671
Turn Signal Replacement Lens ~ Clear
Turn Signal Replacement Lens - Clear - Front or Rear OEM Ref # 4H7-83312-00
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 4H7-83312-00
Carb Float
Carb Float with Pin, Replaces OEM # 16013-329-004 Note: 4 Carb Floats Used Per Bike, Order Quantity you Require
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 30mm OEM Ref # 43120-283-670
Two Metal Speedo / Tach Gauge Covers With Crimp Rings
Two Metal Speedo / Tach Gauge Covers With Crimp Rings. These metal gauge covers are often dented, scratched and corroded. It takes a lot of time to remove the dents, scratches and repaint the covers. With this set of two reproduction gauge covers, you can recondition your gauges so that these will look like new! These covers are unique and the best quality on the market (Made in the United Kingdom). The black metal covers are already painted in the right semi-gloss black colour and are ready to use. This listing contains two black metal covers with crimp rings. These covers lack the hole at the side for speedo meters with the trip meter reset at the side. This hole must be drilled if required.
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Throttle Adjusting Spring
Throttle Adjusting Spring, Replaces OEM # 53191-300-000
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
High Performance Kibblewhite Valve Stem Seal Set
High Performance Kibblewhite 100% Viton Valve Stem Seal Set of 8. Replaces OEM# 12209-333-005. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite Red 100% Viton valve stem seals are designed to have optimum fitment, allow, maximum lift, and to give maximum life. Kibblewhite Red valve stem seals are resistant to high temperatures, petroleum products and the corrosive gasses that are the by-products of combustion. These viton seals retain their ability to seal in situations where other materials could harden and allow oil to enter the combustion chamber causing detonation, carbon build up and a loss of power. The Red Ones are truly the racers choice.
Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Rear Turn Signal Rubbers Pk/2
Rear Turn Signal Rubbers Pk/2, Replaces OEM # 33606-371-000 These are the Rubbers that Go Under the Rear Turn Signal Stays.
Fork Internal Circlip Set
Fork Internal Circlip (48mm) Set/2, Replaces OEM # 94521-48000
Chrome Points Cover
Engine Points Cover ~ Chrome ~ Replaces OEM # 30370-300-020 / 30370-323-000 Points covers are often dented, rusted or worn. A new chrome cover really adds to the look of your bike! If you Require New Hardware for this Cover we carry it # 73-0901.
Valve Tappet Cover Gasket Set/8
Valve Tappet Cover Gaskets Set/8. These are made for the stock type Valve Tappet Covers. These replace OEM # 91302-001-020 Note:These will only work on OEM type Tappet covers
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 38.15mm Diameter x 34mm Height - Replaces OEM # 45107-323-020. Please note: the side with the 2mm outer lip faces the brake pad during install.
Clutch Plate
Clutch Plate 1 Piece Required .138" Thickness OEM Ref # 22202-371-000 / 22202-390-000 / 22202-392-000
Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-216-000 / 18291-MN5-650 Sold Each, Order the Quantity you Require
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach. Fits: All 92mm (3.6") glass lenses. Sold each, order the quantity you require
Ignition Switch Assembly
Ignition Switch Assembly Fork Lock & Keys 5 Prong Socket Connector OEM Ref # 35100-377-003 / 35100-377-007 / 35100-422-017
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Front Fuel Tank Holder Rubber
Front Fuel Tank Holder Rubber - Replaces OEM # 17611-283-010 Sold Each.
Headlamp Rim & Retainer
Headlamp Rim & Retainer Assembly - OEM Ref. # 33101-404-671 / 33101-300-673 / 33101-405-671 / 33100-371-980
Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000