Honda ► CB750A ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750A with universal parts included that match “honda sl125”►
- Honda
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Kick Starter Ratchet Spring
Kick Starter Ratchet Spring. This Ratchet Spring Attaches by the Kick Starter Gear. Replaces OEM # 28253-300-000
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Turn Signal Replacement Lens ~ Smoked
Turn Signal Replacement Lens - Smoked - Front or Rear OEM Ref # 4H7-83312-00
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Rubber Cushion for Cam Chain Roller Shaft
Cam Roller Shaft Rubber (Pk/2) - Replaces OEM # 14607-300-000
Dynatek Dyna S Ignition System (Ultimate Kit)
Dynatek Dyna S Ignition System (Ultimate Kit) with Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System (Premium Kit)
Dynatek Dyna S Ignition System (Premium Kit) with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
7" Halogen Lamp Conversion Kit
7" Halogen Headlamp Conversion unit for Left Hand side of the road driving as in the UK, Japan etc. Lamp unit is Euro E-mark approved and has an internal parking lamp bulb. Lamp unit includes a 12V 60/55 Watt P43T Halogen Bulb with dust boot. 7" Lamp unit fits into stock retainer. Fits: Left hand side of the road Market type bikes (Japan and UK) & for fitting into stock CB750 Retainer (1969-78) models.
Alternator Cover Gasket
Alternator Cover Gasket (Dyno Cover) - OEM Ref. # 11397-300-303
Spark Advance Shaft
Spark Advance Shaft with O-Ring, Replaces OEM# 30231-300-010 / 91301-300-000 The shaft has been nitrate coated to guard against corrosion and it comes with an upgraded Viton O-Ring.
Athena Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850701
Cylinder Base Gasket
Cylinder Base Gasket - OEM Ref. # 12191-300-030
Premium Athena Cylinder Head Gasket
Premium Athena Brand Cylinder Head Gasket - OEM Ref.# 12251-300-050
Oil Pump Gasket
Oil Pump Gasket - OEM Ref. # 15135-300-010
Cam Chain Tensioner Gasket
Cam Chain Tensioner Gasket - OEM Ref. # 14592-300-000
Point Plate Gasket
Contact Point Plate Cover Gasket - OEM Ref. # 30372-300-300
Starter Motor Cover Gasket
Starter Motor Rubber Cover Gasket - OEM Ref. # 31282-300-020
Cam Cover Breather Gasket
Cam Cover Breather Gasket (O-Ring) - OEM Ref. # 12329-300-020
Accelerator Pump Joint Hose
Accelerator Pump Joint Hose. 12" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Order the quantity you require. Note: Be sure to remove and then re-install the old brass nozzles from the old joint hoses.
Carb Overflow Tube Hose
Carb Overflow Tube Hose. 24" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Sold Each, Order the quantity you require
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Rear Sprocket Washer Set
Rear Sprocket Tongued Lock Washer (Pack of 2). Replaces OEM # 94108-17000
Alternator Cover Mounting Screw Set
Alternator Cover Mounting Screw Set. Set of 8 Mounting Screws Used to Fasten the Main Alternator Cover in place (Not the Alternator Face Plate). Replaces OEM # 93500-06032-OA X7 / 93500-06035-OA X1
Stock Type Ignition Coil Set/2 With Brackets
Stock Type Ignition Coil Set/2 With Brackets. Replaces OEM# 30500-300-013 Dual Coil Assembly Pre-Mounted on their Brackets Just Like the Stock Type. Plug and Play Easy Install. Primary 4.3 Ohm, Secondary 15,000k Ohms.
Chrome Starter Motor Cover w Gasket
Chrome Starter Motor Cover with Gasket. Replaces OEM # 31280-300-000 (Cover) and OEM # 31282-300-020 (Gasket). Note: If you Require New Hardware for this Cover this Can be Found on our Site
Ignition Coil Holder Clamp
Ignition Coil Holder Clamp with Bolt, Washer and Nut. This is the clamp that holds the ignition coil in place. Replaces OEM # 30151-300-000 / 30152-300-000
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-405-000
Cam Sprocket
Cam Sprocket, Replaces OEM #14321-392-000 / 14321-300-010
Starting Clutch Gear Seal
Starting Clutch Gear Seal - 25 x 33 x 4 - Replaces OEM # 91215-300-003
High Performance Kibblewhite Valve Stem Seal Set
High Performance Kibblewhite 100% Viton Valve Stem Seal Set of 8. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite Red 100% Viton valve stem seals are designed to have optimum fitment, allow, maximum lift, and to give maximum life. Kibblewhite Red valve stem seals are resistant to high temperatures, petroleum products and the corrosive gasses that are the by-products of combustion. These viton seals retain their ability to seal in situations where other materials could harden and allow oil to enter the combustion chamber causing detonation, carbon build up and a loss of power. The Red Ones are truly the racers choice.
Custom Black Finned Points Cover ~ Joker Machine
Joker Machine Brand ~ Custom Black Finned Points Cover with a Built in Rubber O-Ring and Gold Colored Mounting Hardware, Replaces OEM # 30370-300-020 Brilliant "diamond cut" machining on the outside surface, really gives this piece a cool look! High quality CNC machined cover made in the U.S.A.
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
CB750 Engine Stand
CB750 SOHC Engine Rebuild Stand. Make your engine rebuild a lot easier with this engine stand. Very rigid and easily secured to your work bench using holes found in the base of the stand. Powder coated gloss black for a durable finish. High Quality, Made in the USA.
Intake Valve
Intake Valve OEM Ref # 14711-300-005 / 14711-ME2-000 Made In Japan
Exhaust Valve
Exhaust Valve OEM Ref # 14721-300-005 Made In Japan
Stock Style Tachometer
Stock Style Tachometer, Face dial ranges from 0-12000RPM. The ratio of this Tachometer is 4:1 which is the ratio used on stock CB750's. Note: The CB Tachometers slightly changed from year to year, this may not be an exact stock match for your bike but will work great! Housing Size approx 4.6", face 3.9" Check the photo for the design.
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33406-377-671
Turn Signal Replacement Lens ~ Clear
Turn Signal Replacement Lens - Clear - Front or Rear OEM Ref # 4H7-83312-00
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 4H7-83312-00