Honda ► CB750A ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750A►
- Honda
Oil Pan Gasket
Oil Pan Gasket - OEM Ref.# 11398-425-000
Cylinder Sleeve O-Ring Gasket Set
Cylinder Sleeve O-Rings (Set of 4) OEM Ref. # 91304-286-000 - 4 pc. required per Engine
Valve Tappet Cover Gasket Set/8
Valve Tappet Cover Gaskets Set/8. These are made for the stock type Valve Tappet Covers. These replace OEM # 91302-001-020 Note:These will only work on OEM type Tappet covers
Gear Change Lever
Gear Change Lever Universal Fit
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 5 1/8" Offset 1 3/8"
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Accelerator Pump Joint Hose
Accelerator Pump Joint Hose. 12" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Order the quantity you require. Note: Be sure to remove and then re-install the old brass nozzles from the old joint hoses.
Carb Overflow Tube Hose
Carb Overflow Tube Hose. 24" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Sold Each, Order the quantity you require
Carb Float
Carb Float with Pin, Replaces OEM # 16013-405-004 / 16013-393-004 / 16013-KCY-670 / 16013-MN1-671 Note: Order the Quantity of Floats you Require
Float Bowl Gasket
Float Bowl Gasket (O-Ring)
Fuel Petcock
Fuel Petcock OEM Ref # 16950-393-015 Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Carb Pump Diaphragm
Carb Pump Diaphragm OEM Ref # 16021-393-004 / 16021-393-014 / 16021-MC9-771
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Starter Motor
Rick's Electrics Starter Motor, Replaces OEM# 31200-300-030 This starter motor features an upgraded 4-Brush permanent magnet design & comes with the battery cable.
Rectifier/Regulator
Rick's Electric Brand OEM Style Honda Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier; OE plugs and installation instructions are included. High quality Part.
Wire Harness
Main Wire Harness Loom - OEM Ref. # 32100-393-770 Fits: Honda CB750A (1977-78) Hondamatic
Condenser
Condenser OEM Ref # 30250-300-154 / 30250-300-005
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 51425-375-003 / 51425-375-005
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Steering Bearing Kit
Tapered Roller Steering Bearing Conversion Kit. Superior to OEM quality, 10X the contact area and less flex. Designed as a drop in replacement for the original bearing. Kit is complete with upper and lower tapered bearing races. High quality made in Japan.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Front Wheel Bearing
Front Wheel Bearing with 2 Synthetic Shields - 6302-2RS Size High Quality Made in Japan 2 Used Per Front, Order Quantity you Require
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Reservoir Cap & Diaphragm
Reservoir Cap & Diaphragm Round Thread On Type OEM Ref # 43515-MJ6-006 / 45520-300-000
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45215-533-004
Front Brake Caliper Piston
Front Brake Caliper Piston. Replaces OEM # 45107-392-003
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 178.5mm Width: 39mm OEM Ref # 43120-393-006
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-390-006A
Deluxe Rear Brake Shoe Set
Deluxe Kevlar/Carbon Water Grooved Rear Brake Shoe (Set/2) - OEM Ref # 06430-393-405
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Rear Sprocket Washer Set
Rear Sprocket Tongued Lock Washer (Pack of 2). Replaces OEM # 94108-17000
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Rear Sprocket Bolt & Nut Set
Rear Sprocket Stud Bolt (12x54) & Nut Set. Set includes 4 Stud Bolts and 4 Nuts. These Stud Bolts Fasten to the Centre Wheel Flange and Rear Sprockets. Replaces OEM # 90128-341-000 X4 (Bolts), 94030-12000 X4 (Nut)
Front Brake Rotor
Front Brake Rotor. Replaces OEM# 45120-392-000 / 45120-300-040 / 45120-341-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Carb Holder Set
Carb Holder Set (Set of 4). Replace those old cracked or dried up carb holders with a brand new set! Each holder is numbered 1-4 just like the original OEM holders. Replaces OEM#'s 16211-393-020 #1, 16212-393-020 #2, 16213-393-010 #3, 16214-393-010 #4 We have had these re-manufactured as they have been discontinued by Honda for years! Fits: Honda CB750A (1977-78) Hondamatic Clamps required: 4pcs 15-0684, 4 pcs 15-0688
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb