Honda ► CB750C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750C►
- Honda
Drive Chain Adjuster Set
Complete Drive Chain Adjuster Set, Includes 2 Chain Adjusters, 2 Chain Adjusting Bolts and 2 Adjuster Nuts. Replaces OEM # 40543-425-000
Positive (+) Battery Cable
Positive (+) Battery Cable with Rubber End Covers. Replaces OEM # 32401-425-010
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-MA3-840
Horn Sub Harness
Horn Sub Harness "B", This is the Harness that Attaches to the Horn. Replaces OEM # 32102-463-601
Starter Motor Cable
Starter Motor Cable, Replaces OEM # 32402-425-000
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Engine Bolt Set
Engine Bolt Set, 54 Pieces and 3 Allen Keys Included.
Valve Shim Kit
20 Piece Valve Shim Kit with Plastic Case, 25mm Diameter Valve Shims. Includes 2 of each of the following sizes. 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00, 3.10.
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Speedometer Cable
Speedometer Cable - OEM Ref # 44830-MA5-670 Made in Japan
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Carb Fuel Connector Tube and Accellerator Tube O-Rings
Carburetor Fuel Connector Tube and Accellerator Tube O-Rings, 12 O-Rings.
Stock Type Gearshift Lever Rubber
Stock Type Gearshift Lever Rubber, Replaces OEM # 24781-419-000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-ME1-670
Brake Pedal Return Spring
Brake Pedal Return Spring. This is the Spring Used where the Brake Pedal Attaches to the Brake Spindel. Replaces OEM # 46514-425-010
Cam Chain Tensioner Spring "B"
Cam Chain Tensioner Spring "B". This is the Cam Chain Tensioner Spring for the Smaller Cam Chain Tensioner ("B"). Replaces OEM # 14538-425-000
Starter Clutch Roller Spring
Starter Clutch Roller Spring, Replaces OEM # 28125-516-030 Sold Each, Order the Quantity you Require
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-425-000
Rear Brake Shoe Spring Set/2
Rear Brake Shoe Spring Set of 2. Replaces OEM # 43151-346-000
Spark Advancer Cover Screw Set
Spark Advancer Cover Screw Set of 3, Screw Size 6x25, Replaces OEM # 93700-06025-0A
Clutch Spring Bolt Set
Clutch Spring Bolt Set of 6. Replaces OEM # 95725-06025-00 X6.
Side Cover Hook Rubber
Side Cover Hook Rubber Used to hold the Side Cover in place. Replaces OEM # 83601-425-870
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-425-670
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Carburetor Needle Jet Holder
Carburetor Needle Jet Holder, Replaces OEM # 16165-422-004 Note: Sold Each
Tach Drive Oil Seal
Tach Drive Oil Seal - 4.8 x 14.5 x 5 - Replaces OEM # 91256-425-003
Clutch Arm Oil Seal
Clutch Arm Oil Seal - 10 x 16 x 4.5 - Replaces OEM # 91259-VM0-000
Crank Seal
Crank Seal - 25 x 42 x 8 - Replaces OEM # 91201-425-003
Oil Pump Shaft Seal
Oil Pump Shaft Seal - 25 x 47 x 10 - Replaces OEM # 91257-425-013
Shift Shaft Oil Seal
Shift Shaft Oil Seal - 12.5 x 25 x 8 - Replaces OEM # 91204-425-003
Countershaft Oil Seal
Countershaft Oil Seal - 40 x 62 x 13.5 - Replaces OEM # 91205-425-003
Cylinder Head Stud Bolt
Cylinder Head Stud Bolt (8 x 55). Replaces OEM # 90035-425-000
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Jet Needle Set
Jet Needle Set. Replaces OEM # 16012-425-771 Includes Contents show in photo.
Pilot Jet Set ~ Size #35 (Pk/4)
Pilot Jet Set of 4 (Size #35), Replaces OEM # 99103-GY6-0350 Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible.
Idle Slow Circuit Nozzle (Pk/4)
Idle Slow Circuit Nozzle (Pk/4), Replaces OEM # 16166-425-671
High Performance Kibblewhite Valve Spring Set
High Performance Kibblewhite Valve Spring Set of 16. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. The springs in these kits are wound from super clean chrome silicon wire that has been heat treated and shot peened. These components offer optimal fitment, keeping lateral movement to a minimum. They work together as a system, providing long life, and maximum performance.
High Performance Kibblewhite Intake/Exhaust Valve Guide
High Performance Kibblewhite Intake or Exhaust Valve Guide (Standard Size). Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite uses the copper based C63000 nickel-aluminum bronze as a material to make these bronze valve guides because of its ideal characteristics for the application. The 5% nickel content provides superior resistance to wear, and the approximately 80 percent copper content delivers outstanding heat conductivity. Kibblewhite guide profiles are designed to have minimal effect on the airstream while maintaining critical cross sectional thickness in high temperature areas, which promotes high performance and endurance. Sold Each, Order the Quantity you Require
High Performance Kibblewhite Valve Stem Seal Set
High Performance Kibblewhite 100% Viton Valve Stem Seal Set of 16. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite Red 100% Viton valve stem seals are designed to have optimum fitment, allow, maximum lift, and to give maximum life. Kibblewhite Red valve stem seals are resistant to high temperatures, petroleum products and the corrosive gasses that are the by-products of combustion. These viton seals retain their ability to seal in situations where other materials could harden and allow oil to enter the combustion chamber causing detonation, carbon build up and a loss of power. The Red Ones are truly the racers choice.
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Side Stand Rubber Hardware Set
Side Stand Rubber Hardware Set, Includes Metal Collar and Silver Colored Flange Bolt.
Turn Signal Lamp Lens Screw Set
Turn Signal Lamp Lens Screw Set/2, Replaces OEM # 93500-04025-0A ALSO Fits our Signal Lens #11-2195 and Signals #11-2114 and #11-2149
Carb Bolt Kit
Carburetor Bolt and Washer 43 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Rear Wheel Damper Rubber
Rear Wheel Drive Damper Rubber, Replaces OEM # 41241-300-050 These fit between the rear wheel sprocket hub and the wheel hub and get worn down over time from use. Note: 4 Used Per Bike, Order The Quantity you Require