Honda ► CB750F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750F with universal parts included►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 135mm Length. Replaces OEM #' 53165-342-670 / 53166-342-670
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35200-374-671
Bar Switch Assembly ~ Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side - Black. Replaces OEM # 35130-404-671
Bar Switch Assembly ~ Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side - Black. Replaces OEM # 35130-461-770 / 35130-463-670 / 35130-461-770
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35200-460-671 / 35200-425-672 / 35200-445-671
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35200-410-671
Handlebar - Stock Type ~ CB750K 1973-76 / CB750F 1975-76
Stock Type Handlebar for the CB750K (1973-76), CB750F (1975-76) - Chrome. Drilled for wires like the OEM type. Bar Diameter - 7/8" - 22mm, Length - 32" - 812mm, Pull Back - 5 1/4" - 133mm, Inner Rise - 6 1/2" - 165mm, End Rise - 8" - 203mm, Center Width - 6 1/2" - 165mm, Base Width - 9 1/2" - 241mm, Knurl Width - 4 1/2" - 114mm, Control Length - 9" - 228mm, Drilled - YES Replaces OEM # 53100-341-700 Note: These Are Drilled For Wires
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/4" Inside Length x 7/8" 150mm Length
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/8" Inside Length x 7/8" 140mm Length
Grips
Ribbed Grip Set Yamaha OEM Type - Black With Closed Ends 5" Inside Length x 7/8" 120mm Length