Honda ► CB750F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750F►
- Honda
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-425-000 / 22202-MT8-000
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Steel Clutch Plate "B" ~ Riveted Plate
Steel Clutch Drive Plate "B" - OEM Ref # 22322-425-000 This is the thick double steel plate with rivets in it. It is an essential part of any clutch rebuild as the rivets are known to wear over time. 1PC Required per Bike
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Steel Clutch Plate
Steel Clutch Plate 5 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Clutch Spring Kit
Clutch Spring Kit
Carb Holder Set
Carb Holder Set (Set of 4)
Intake Carb Holder Set
Intake Carb Holder Set OEM Ref # 16214-425-00 1 Pc, 16213-425-00 1 Pc, 16212-425-00 1 Pc, 16211-425-00 1 Pc NOTE-If you require band clamps, these carb holders require our clamps part #15-0689 X8
Carb Holder Set
Carb Holder Set (Set of 4). Replace those old cracked or dried up carb holders with a brand new set! Each holder is numbered 1-4 just like the original OEM holders. Replaces OEM #'s 16211-410-000 / 16212-410-000 / 16213-410-000 / 16214-410-000 NOTE-If you require band clamps, these carb holders require our 45-47mm diameter clamps part #15-0688 X8.
Carb Air Box Rubber Boot
Carburetor to Air Box Rubber Boot. Replaces OEM # 17253-341-300 Note: 4 Boots Used Per Bike, Order Quantity you Require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-341-004
Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Carb Top Gasket, D313 Slide Needle, Main Jet (#105, Stock type for 1977-78F models), Main Jet #110, Stock type for 1978K model), Float Needle, Air Spring, Air Screw Plug, E-Clip, Air Fuel Screw (1978F Type), Air Fuel Screw (1977-78K Type), Needle Jet, Metal Washer, 6 O-Rings. - Made in Japan -
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).
Ultimate Performance Main Jet Kit
Ultimate Performance Main Jet Kit. Kit includes a total of 44 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #100 (X4), #102 (X4), #105 (X4), #108 (X4), #110 (X4), #112 (X4), #115 (X4), #118 (X4), #120 (X4), #122 (X4) and #125 (X4)
Pilot Jet Set/4
Stock Type Pilot Jet Set of 4 (Size #35). Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Note: These Pilot Jets (#35) were the standard size equipped from the factory
Pilot Jet Set (Pk/4)
Stock Type Pilot Jet Set of 4 (Size #40). Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Fits: Honda CB750K (1972-76) with original stock carbs CB750F (1975-76) with original stock carbs Note: These Pilot Jets (#40) were the standard size equipped from the factory.
Rubber Passage Plug
Rubber Passage Plug Pk/5 OEM Ref # 16010-425-671 / 16010-461-781 / 16010-469-004
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-382-004 / 16011-393-004 / 16011-KG0-891 / 16030-1007 / 16011-382-004
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-413-751 / 16155-397-971
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Press In Pilot Jet Set/4 ~ #35 Size
Press In Pilot Jet Set/4 ~ #35 Size Please Double Check you Require the Stock #35 Size Before Ordering
Air Cut Off Valve With Cover
Carb Air Cut Off Valve with Cover - OEM # 16048-429-771 (Diaphragm), 16048-425-771 (Spring + 1 O-Ring), 16048-429-771 (Cover).
Float Bowl Screws Pk/2
Float Bowl Screws with Lock Washers, Pack of 2 Screws and 2 Washers. These fasten the float bowl in place. Replaces OEM # 93892-04016-00 Order Quantity of Screws you Require
Press In Pilot Jet Set/4 ~ #38 Size
Press In Pilot Jet Set/4 ~ #38 Size Please Double Check you Require the #38 Size Before Ordering
Press In Pilot Jet Set/4 ~ #40 Size
Press In Pilot Jet Set/4 ~ #40 Size Please Double Check you Require the #40 Size Before Ordering
Press In Pilot Jet Set/4 ~ #42 Size
Press In Pilot Jet Set/4 ~ #42 Size Please Double Check you Require the #42 Size Before Ordering
Fuel Tank Emblem
Fuel Tank Emblem with 2 Attachment Clips - Replaces OEM# 87122-410-000 , 87121-410-000. High quality made of cast metal. Note: Sold Each, Order 2 if replacing the emblems on both sides of the fuel tank.
Side Cover Emblem 1978F
Side Cover Emblem with 2 Attachment Clips. Replaces OEM# 87127-410-770 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach. Fits: All 92mm (3.6") glass lenses. Sold each, order the quantity you require
Speedometer & Tachometer Crimp Ring Set/2
Speedometer & Tachometer Crimp Ring Set/2. When changing the speedometer or tachometer face plates these rings are often damaged. Get a new set today to have your speedo & tachometer restoration looking perfect! Dimensions: Inner diameter 102.7mm. - Outer diameter 107.5mm.
Speedometer & Tachometer Replacement Glass Lens Set/2
Speedometer & Tachometer 92mm Glass Lens Set/2. If the glass lens of your gauges have scratches or are broken, with these glass lenses you are able to repair your gauges' lenses. These glass lenses are slightly bent like the original glass lenses.
Two Metal Speedo / Tach Gauge Covers With Crimp Rings
Two Metal Speedo / Tach Gauge Covers With Crimp Rings. These metal gauge covers are often dented, scratched and corroded. It takes a lot of time to remove the dents, scratches and repaint the covers. With this set of two reproduction gauge covers, you can recondition your gauges so that these will look like new! These covers are unique and the best quality on the market (Made in the United Kingdom). The black metal covers are already painted in the right semi-gloss black colour and are ready to use. This listing contains two black metal covers with crimp rings. These covers lack the hole at the side for speedo meters with the trip meter reset at the side. This hole must be drilled if required.
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal. This internal rubber seal replaces the ripped, dried or missing rubber internal seal. This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 1X - 4x8 Screws w Lock Washers 11X- 4x12 Screws w Lock Washers 12X- 4x16 Screws w Lock Washers
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
OEM Type Shock Absorber Bolt
Chrome Shock Absorber Bolt, Replaces OEM # 93201-10032-0B / 93200-10032-0A Note: 2 Bolts Used Per Bike, Order the Quantity you Require
Alternator Cover Mounting Screw Set
Alternator Cover Mounting Screw Set. Set of 8 Mounting Screws Used to Fasten the Main Alternator Cover in place (Not the Alternator Face Plate). Replaces OEM # 93500-06032-OA X7 / 93500-06035-OA X1
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.