Honda ► CB750K ►
-
Here’s our hand-picked list of electrical parts for your Honda CB750K with universal parts included that match “honda sl125”►
- Honda
Starter Motor Cable
Starter Motor Cable, Replaces OEM # 32402-425-000
Ignition Coil Holder Clamp
Ignition Coil Holder Clamp with Bolt, Washer and Nut. This is the clamp that holds the ignition coil in place. Replaces OEM # 30151-300-000 / 30152-300-000
Custom Black Finned Points Cover ~ Joker Machine
Joker Machine Brand ~ Custom Black Finned Points Cover with a Built in Rubber O-Ring and Gold Colored Mounting Hardware, Replaces OEM # 30370-300-020 Brilliant "diamond cut" machining on the outside surface, really gives this piece a cool look! High quality CNC machined cover made in the U.S.A.
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33406-377-671
Turn Signal Replacement Lens ~ Clear
Turn Signal Replacement Lens - Clear - Front or Rear OEM Ref # 4H7-83312-00
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 4H7-83312-00
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-MA3-840
Fuse Box Assembly
Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM # 38200-425-005
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
Negative (-) Battery Cable
Negative (-) Battery Cable (Ground Cable). Replaces OEM # 32601-MG9-000
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Ignition Switch Assembly
Ignition Switch Assembly Fork Lock & Keys 5 Prong Socket Connector OEM Ref # 35100-377-003 / 35100-377-007 / 35100-422-017
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Headlamp Rim & Retainer
Headlamp Rim & Retainer Assembly - OEM Ref. # 33101-404-671 / 33101-300-673 / 33101-405-671 / 33100-371-980
Fender Eliminator Taillight
Fender Eliminator 12 Volt Taillight with 2 Wires. This fits to our fender eliminator (#73-1144) and looks great! Note: Photo shows Taillight Mounted to Fender Eliminator #73-1144 for Reference Only, it is not included with this item. Please purchase it separate
Bar Switch Assembly ~ Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side - Black. Replaces OEM # 35300-300-672 Note: Wiring to be run Inside the handlebar. This is a single throttle cable configuration type assembly.
Alternator Brush Set
Alternator Brush Set/2 18 x 5 x 4.5mm Works With Electromagnetic Rotors OEM Ref # 31124-MG5-000 / 31124-422-005 / 31125-422-000
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-300-000
Starter Motor Bolt (Set/2)
Starter Motor Flange Bolt Set/2. Replaces OEM # 95700-06056-00
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Rear Brake Light Stop Switch Bracket
Rear Brake Light Stop Switch Bracket, Replaces OEM # 50156-300-020
Ignition Switch Mounting Bracket & Hardware Set
Ignition Switch Mounting Bracket & Hardware Set. Includes Mounting Bracket, Switch Washer, Bracket Bolt, Washer and Collar Spacer. Replaces Mounting Bracket OEM # 50375-300-000B
Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek 3 Ohm coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.
Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.
Dynatek Dyna 2000 Digital Perfomance Ignition
Dynatek Dyna 2000 Digital Performance CDI Ignition. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek.
Fuse Box Assembly
Fuse Box Assembly Complete with 3 Extra Fuses, Replaces OEM # 32110-300-000
Turn Signal Lamp
Turn Signal Lamp - Front 2-Wire OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-341-672
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35200-404-671 Note: This handlebar switch assembly requires the wires to be run inside the handlebar
Ignition Coil
Ignition Coil Stock type for contact point ignitions. 100mm center to center mounting points. OEM Ref # 30501-300-03 / 30501-300-013 / 30502-300-003 / 30502-300-013
Horn Sub Harness "A"
Horn Sub Harness "A", This is the Harness that Attaches to the Horn. Replaces OEM # 32101-438-000
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set (8 Pc. Set). This set is used to mount your tail Light to the tail Light bracket. Each set Includes 2X Rubber Grommets, 2X Collars, 2X Bolts and 2X Washers.
Front Signal Lamp Stay Nut & Washer Set
Front Signal Lamp Stay Nut & Washer Set. These are the Nuts and Washers that thread into the Front Turn Signal Stays. Set includes 2 Nuts and 2 Washers, Enough for both Front Signal Stays.
Turn Signal Replacement Lens ~ Clear
Turn Signal Replacement Lens - Clear - Front Or Rear OEM Ref # 33402-431-782
Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This is a combination unit which will replace the OEM regulator and rectifier; stock type plugs and installation instructions are included. Dimensions 70mm Length, 94mm Width, 27mm Height, Hole Distance 80mm Center to Center. Note: May require a custom mounting job. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013