Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included that match “wire harness”►
- Honda
Alternator Stator Wire Harness
Alternator Stator Wire Harness, This Harness has the Same 7 Wire Plug as the OEM part and Hooks up Without Alterations. Replaces OEM # 31110-300-154
Horn Sub Harness
Horn Sub Harness, This is the Harness that Attaches to the Horn. Replaces OEM # 38105-369-000
Oil Pressure Switch Wire Assembly
Oil Pressure Switch Wire Assembly. Includes the Wire and Rubber Cover. Replaces OEM # 31270-300-154 / 31270-300-005
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Dynatek Dyna 2000 Digital Perfomance Ignition
Dynatek Dyna 2000 Digital Performance CDI Ignition. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek.
Pilot Indicator Light Cover
Pilot Indicator Light Cover, Replaces OEM# 37600-377-018 This includes the front and rear cover with fastening screws.
Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek 3 Ohm coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.
Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)
Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA. Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting. Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.
Rectifier Regulator
Universal Type Rectifier Regulator 8 Wires - No End Terminals
NGK Spark Plug
NGK D8EA Spark Plug - Standard Original CB750 Spark Plug 4 required per CB750, Order the quantity you require.
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.
Turn Signal Lamp
Turn Signal Lamp - Front 2-Wire OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Turn Signal Lamp
Turn Signal Lamp 1-Wire - Rear OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Dynatek Dyna S Ignition System (Ultimate Kit)
Dynatek Dyna S Ignition System (Ultimate Kit) with Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System (Premium Kit)
Dynatek Dyna S Ignition System (Premium Kit) with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance! This ignition can be used with your stock coils or any other coils 3 ohms or higher.
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35200-404-671 Note: This handlebar switch assembly requires the wires to be run inside the handlebar
Rectifier/Regulator
Rectifier-Regulator: This is a combination unit which will replace the OEM regulator and rectifier. This has the OEM type ground wiring and Stock Type Plugs. Dimensions 80mm Length, 94mm Width, 27mm Height, Hole Distance 70.0mm Center to Center. Instructions not included.
Handlebar - Stock Type ~ CB750K 1977-78
Stock Type Handlebar for the CB750K (1977-78) - Chrome. Bars are not drilled for wires. Bar Diameter - 7/8" - 22mm, Length - 31" - 787mm, Pull Back - 5 1/4" - 133mm, Inner Rise - 7" - 178mm, End Rise - 9" - 228mm, Center Width - 6" - 152mm, Base Width - 9 1/2" - 241mm, Knurl Width - 4 1/2" - 114mm, Control Length - 8 1/2" - 216mm, Drilled - YES Replaces OEM # 53100-405-010
120Pc ~ 3.5mm Bullet Connector with Covers Set ~ For Wire Harness
120Pc ~ 3.5mm Bullet Connector with Covers Set ~ For Use on Wire Harness's. Wire harness's typically require these special 3.5mm sized connectors. So, this set is just what you need if working on the harness! Includes 30 Male and 30 Female Bullet Connectors and 60 Covers. Made of High Quality Brass, Durable, Corrosion Resistant, Low Resistance, Gives the Best Electric Flow. Includes Plastic Case.
Bar Harness
Bar Harness Eliminates Damage To Fairings, Grips & Body Covers Red Heavy Duty Nylon Web 1 3/4" x 37"
Cylinder Wire Set
Cylinder Wire Set Black Gum Rubber - Copper Core 2 Pcs 15" Long 2 Pcs 12" Long
Master 360pc Terminal Shop Set with Plastic Case
Master 360pc Terminal Shop Set with Plastic Case. This set will cover any and all of your motorcycle terminal and terminal cover needs. Included is 20pcs of each of the following terminals and terminals covers. Terminals 6.25mm Ring Connectors, Metric Terminal - Round Female type Pin Connector, Metric Terminal - Round Male type Pin Connector, Metric Terminal - Round Double Female type Pin Connector, Metric Terminal - Flat Male Spade type Terminal, Metric Terminal - Flat Female Spade type Terminal, 250 Type Flag Terminals, Metric Terminal - Small Flat Male Spade type Terminal, Metric Terminal - Small Flat Female Spade type Terminal, Metric Terminal - Round Male Small type pin Connector, Metric Terminal - Round Female Small type pin Connector, Metric Terminal - Round Triple Female type Pin Connector. Terminal Covers Metric Terminal Cover - Round type Female Cover, Metric Terminal Cover - Round type Male Cover, Metric Terminal Cover - Round type Double Female Cover, Metric Terminal Cover - Flat Female Spade Cover, 250 Type Flag Terminal Covers, Metric Terminal Cover - Round type Triple Female Cover
Relay with Base ~ 4 Pin ~ 12v 40Amp
Relay with Base ~ 4 Pin ~ 12v 40Amp. This relay is typically used for on/off applications such as horn/aux lights etc.
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Relay with Base ~ 5 Pin ~ 12v 40Amp.
Relay with Base ~ 5 Pin ~ 12v 40Amp. This relay is typically used for hi/low beam applications.
Universal Bar Switch Assembly ~ Left (Clutch) Side
Universal Bar Switch Assembly ~ Left (Clutch) Side. Clutch side universal handlebar switch for 7/8" bars. Simple and clean design with the essentials. Includes headlight hi-low, turn signal and horn buttons. Includes 8 female bullet connectors, you may need to adapt the connectors to fit your wire harness.
Universal Bar Switch Assembly ~ Right (Brake) Side
Universal Bar Switch Assembly ~ Right (Brake) Side. Brake side universal handlebar switch for 7/8" bars. Simple and clean design with the essentials. Includes momentary starter, kill and on/off headlight buttons. Includes 9 female bullet connectors, you may need to adapt the connectors to fit your wire harness.
Coil High Tension Wire Ends (Pk/2)
Coil High Tension lead ends (fit inside coil towers) (Pk/2) Fits: #17-6810 Coil
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
600Pc Round Style Wire Crimp Bullet Terminal Set with Covers in Plastic Storage Case
600Pc Round Style Wire Crimp Bullet Terminal Set with Covers in Plastic Storage Case. Includes insulated male (150pcs) and female (150pcs) wire connectors with (300pcs) compatible covers. 4.0mm Diameter Brass Sleeves Plug type.
Custom Chrome Dual Beam Headlights
Custom Chrome 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
Custom Matte Black Dual Beam Headlights
Custom Matte Black 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.