Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Carb Stabilizer Bracket
Carburetor Stabilizer Bracket. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!
Accelerator Pump Joint Hose
Accelerator Pump Joint Hose. 12" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Order the quantity you require. Note: Be sure to remove and then re-install the old brass nozzles from the old joint hoses.
Carb Overflow Tube Hose
Carb Overflow Tube Hose. 24" Piece. 8mm Outer Diameter, 4mm Inner Diameter. Sold Each, Order the quantity you require
Carb Float
Carb Float with Pin, Replaces OEM # 16013-300-004
Carb Float Setting Tool (CB750 1969-76 Models)
Carb Float Setting Tool. Use this tool to help set your floats with ease! This pre-set float setting gauge is for the CB750 1969-76K and 1975-76F Supersport models.
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16023-300-004
Carb Holder Set
Carb Holder Set (Set of 4)
Carb Air Box Rubber Boot
Carburetor to Air Box Rubber Boot. Replaces OEM # 17253-341-300 Note: 4 Boots Used Per Bike, Order Quantity you Require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Deluxe Carb Rebuild Kit
Carb Rebuild Kit. Contains: Float Bowl Gasket, Top Cover Gasket, Float Needle (2.0) & Seat with Float Needle Washer, Main Jets #120 and #140, Slow Jet (#40), Slide Needle & Clip, Air Screw & Spring, Jet Needle Retainer and Assorted Washers. - Made in Japan -
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
1969-70 Performance Main Jet Kit
1969-70 Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #140 (X4), #142 (X4), #145 (X4), #148 (X4)
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Carburetor Needle Jet Holder
Carburetor Needle Jet Holder. Replaces OEM # 16139-300-004 Note: Sold Each, One Used per Carburetor
Throttle Cable
Throttle Cable - Single top cable to 4 individual Carbs OEM Ref. # 17910-300-030 Made in Japan
Gear Clamp 40-60mm.
Universal Gear Clamp for Carb Holders or Air Boxes. 9mm Wide. Adjusts with a screwdriver. Fits: Diameters 40-60mm (With a width of 9mm)
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 53-56mm. (1.92" - 2.16")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 60mm-65mm or 2.36" to 2.56"
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 41-44mm. (1.53" - 1.69")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 46-49mm. (1.77" - 1.92")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 66-69mm. (2.48" - 2.63")
Universal Band Clamp
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 69-72mm. (2.67" - 2.87")
Band Clamp 45-47mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 45-47mm.
Band Clamp 50-52mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 50-52mm.
Band Clamp 58-60mm.
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 58-60mm.
Band Clamp 43-49mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 43-49mm. (1.69"-1.93") Diameters
Band Clamp 67mm-73mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 67-73mm. (2.64"-2.87") Diameters
Band Clamp 73mm-79mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 73-79mm. (2.87"-3.11") Diameters
Band Clamp 79-85mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifold to Filter Joints and all purpose uses except carb holders. Fits: 79-85mm. (3.11"-3.35") Diameters
Band Clamp 85-91mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 85-91mm. (3.35"-3.58") Diameters
Band Clamp 91-97mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 91-97mm (3.58"-3.82") Diameters
Band Clamp 97mm-103mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 97-103mm (3.82"-4.00") Diameters
Band Clamp 103mm-109mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 103-109mm (4.00"-4.29") Diameters
Band Clamp 109mm-115mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 109-115mm (4.29"-4.53") Diameters
Band Clamp 115mm-121mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 115-121mm. (4.53"-4.76") Diameters
Band Clamp 121mm-127mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifolds to Filter Joints and all purpose uses except carb holders. Fits: 121-127mm. (4.76"-5.00") Diameters
Band Clamp 37-43mm
Band Clamp for Air Filters, Airbox to Carb Joints, Custom Manifold to Filter Joints and all purpose uses except carb holders. Fits: 37-43mm. (1.45"-1.69") Diameters
Band Clamp 78-80mm
Universal Band Clamp for Carb Holders or Air Boxes Fits: Diameters 78-80mm.
Carb Float Level Gauge
Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors. Adjustable Width: 16-78mm and Adjustable Height 0-40mm
Hose Remover Pliers
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
382pc O-Rings Kit with Plastic Case
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm 10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm 10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm 10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm 10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm 10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm 10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Carburetor Synchronizer Vacuum Gauge ~ 2,3,4 Cylinders
Carburetor and throttle body synchronizer kit for bikes with 2, 3 or 4 Cylinders. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2, 3 or 4 cylinders. Includes 4 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from 0.45mm to 1.5mm.
Fluid Hose Clamp
Fluid Hose Clamp, all steel construction with adjustable locking collar. Completely or partially closes flexible brake, fuel, and vacuum fluid lines.
Portable Auxiliary Fuel Tank Tool
Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed. Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
Carburetor Synchronizer Vacuum Gauge ~ 2 Carb Synchronizer
Carburetor and throttle body synchronizer kit for bikes with 2 Carbs. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2 carbs. Includes 2 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.