Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K►
- Honda
Oil Pump Rebuild Kit
11 Pc. Oil Pump Rebuild Kit. Use this kit to get your oil pump flowing at maximum capacity for a healthy engine, performing at it's best! Kit includes 1 oil stopper seal, 1 oil stopper spring, 1 oil relief valve spring, 1 oil relief valve o-ring, 3 pump connection o-rings, 2 inner rotor o-rings, 1 steel reinforced center shaft seal, 1 pump body gasket.
Rear Wheel Damper Rubber
Rear Wheel Drive Damper Rubber, Replaces OEM # 41241-300-050 These fit between the rear wheel sprocket hub and the wheel hub and get worn down over time from use. Note: 4 Used Per Bike, Order The Quantity you Require
Shock Absorber Set ~ Stock Design ~ CB750K 1972-76
Stock Type Designed Shock Absorber Set - Chrome Body with Chrome Springs and Chrome Center. These are modelled after the original stock shocks made for the CB750K 1972-76. The original OEM shocks came with 3 position spring preload adjustments however we have upgraded these to 5 spring preload adjustments so you can better fine tune these shocks! 336mm (13 1/4") Center of Eye to Clevis. Stock Match for: Honda CB750K (1972-76) Will Also Fit: Honda CB750K (1969-71), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Chain Oiler Plug ~ Joker Machine
Joker Machine Brand ~ Chain oiler (final shaft) plug eliminates the messy chain oiler assembly with one of these simple plugs! Replaces OEM # 23523-300-310 Installs easily by cleaning hole with brake cleaner to remove all traces of oil. Then fill with RTV slicone (Permatex) and tap the chain oiler plug in place. High quality CNC machined part made in the U.S.A.
Custom Type Black Fork Caps (Set/2) ~ Joker Machine
Joker Machine Brand ~ Custom Black Fork Cap Set of 2 with O-Rings. Replaces OEM # 90123-300-000 High quality CNC machined from billet aluminum, much lighter then the stock type. Gives your bike a great custom look. Made in the U.S.A.
Custom Black Horn with Bracket ~ Joker Machine
Joker Machine Brand ~ Small Custom Black Horn with CNC Machined Bracket and 2 Gold Mounting Screws. This horn relocates to the center-line of the frame instead of the stock horn's offset position. This custom small horn gives your bike a racy billet look and enables better clearance for steering damper installations. High quality made in the U.S.A.
Chrome Kick Starter Shaft Cover ~ Joker Machine
Joker Machine Brand ~ Chrome Kick Starter Shaft Cover. Eliminates the heavy kick starter arm and cleans up the look of the splined shaft. Installs in seconds with a set screw from underneath. High quality CNC machined part, Made in the U.S.A.
Oil Pressure Gauge Assembly ~ Silver ~ Joker Machine
Joker Machine Brand ~ Oil Pressure Gauge Assembly. Silver Colored Mount Assembly with a Silver Colored Stainless Steel Marshall liquid filled gauge 1 1/2" (38mm) diameter, 0 to 100 PSI. Easily installs on the oil gally port above the points cover in minutes! Features 2 built-in Neoprene rubber o-rings recessed in 2 fittings that have a unique rotating section that enables you to easily position the gauge for perfect rider visability. Just loosen the billet hex fitting, rotate into position, then tighten. High quality made in the U.S.A
Custom Black Finned Points Cover ~ Joker Machine
Joker Machine Brand ~ Custom Black Finned Points Cover with a Built in Rubber O-Ring and Gold Colored Mounting Hardware, Replaces OEM # 30370-300-020 Brilliant "diamond cut" machining on the outside surface, really gives this piece a cool look! High quality CNC machined cover made in the U.S.A.
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Tach Drive Plug Block Off ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Tach Drive Plug (Block Off). This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. High quality CNC machined part, made in the U.S.A.
Rear Stock Type Rim
Chrome Rear Stock Type Rim, 2.15" Width x 18" x 40 Hole, Overall Actual Width 3.15". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 42701-300-013
Front Stock Type Rim
Chrome Front Stock Type Rim, 1.85" Width x 19" x 40 Hole, Overall Actual Width 2.75". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 44701-405-771
Starter Motor
Starter Motor Unit. Replaces OEM # 31200-438-505 This starter bolts on as direct replacements for the OEM type. Features an improved high-output permanent magnet.
Fork Tube Set
Fork Tube Set/2, Length (605mm or 23 13/16"), 35mm OD. NOTE: LENGTH is 23 13/16", one Inch Larger then Stock Length for these Models below. Fits: Honda CB750K (1972) Higher then Frame# 2093730 Only, CB750K (1973-76) Also Fits These Models, Confirm the 605mm Length is what you Require Before Ordering Honda CB750K (1977) Higher then Frame# 2707508 Only, CB750K (1978), CB750F (1977-78) Supersport, CB750A (1976-78) Hondamatic Before ordering Please Confirm 23 13/16" or 605mm is the Length you would like
Fork Tube Set
Fork Tube Set/2, Length (585mm or 23"), 35mm OD. Fits: Honda CB750K (1969-71), CB750K (1972) Lower then Frame# 2093730 Only Before ordering Please Confirm 23" is the Length you would like
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No chrome trim or hardware included just re-use existing hardware). There is NO HONDA LOGO ON THE REAR. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB750K (1972-76) Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Seat Cover
Replacement Seat Cover with Reinforced Passenger Strap (No hardware or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB750K (1978) Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Seat Cover
Replacement Seat Cover (No hardware or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB750K (1980-82) Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Cast Aluminum Finned Starter Motor Cover
Cast Aluminum Finned Starter Motor Cover, Made in the USA. Replaces OEM # 31280-300-000 This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine. Note: Gasket and Hardware Not Included with Cover
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Shock Absorber Set
Shock Absorber Set - Black Body with Black Springs - 365mm (14 3/8") Eye to Clevis. 4 Position spring preload adjustment, progressive wound heavy duty springs. Includes bushings, inserts, washers and spring preload wrench.
CB Chrome Mirror - Early Stock Type
CB750 Eary Stock Type Chrome Mirror - 4" Diameter Mirror, 8" Stem, 10mm. RH Thread. Replaces OEM # 88110-300-000 Note: These Fit Both Left And Right Side Of Bike, Order 2 For A Complete Set
Rear Turn Signal Grounds (Pk/2)
Rear Turn Signal Ground Cables (Pk/2), Replaces OEM # 33620-300-000 These Cables are Needed in order to Ground the Rear Turn Signals, Overall Length 550mm.
Ignition Switch Mounting Bracket & Hardware Set
Ignition Switch Mounting Bracket & Hardware Set. Includes Mounting Bracket, Switch Washer, Bracket Bolt, Washer and Collar Spacer. Replaces Mounting Bracket OEM # 50375-300-000B
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50710-405-000
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Valve Spring Seat (Inner)
Valve Spring Seat (Inner), Replaces OEM # 14776-422-000 Sold Each, Order the Quantity you Require.
Valve Spring Seat (Outer)
Valve Spring Seat (Outer Seat), Replaces OEM # 14775-422-000 Sold Each, Order the Quantity you Require.
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-329-000 Sold Each, Order the Quantity you Require.
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-551-020 Sold Each, Order the Quantity you Require.
Steering Stem Washer
Steering Stem Washer, Replaces OEM # 90503-425-000 Sold Each, order the quantity you require.
Steering Stem Nut
Steering Stem Nut, Replaces OEM # 90304-425-000 Sold Each, we also offer the washer for this nut
Swing Arm Felt (Set/2)
Swing Arm Felt (Set/2), Replaces OEM # 52145-283-000
Swing Arm Pivot Bolt Lock Nut and Washer
Swing Arm Pivot Bolt Lock Nut and Lock Nut Washer, Replaces OEM # 90354-425-830 (Nut), 90600-425-830 (Washer)
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Horn Hardware Set
Horn Hardware Set, Includes 2 Bolts and 2 Washers. Replaces OEM # 92101-06016-0A X2 (Bolt) and OEM # 94111-06000 X2 (Washer).
Cylinder Head Cam Cover Breather Hardware Set
Cylinder Head Cam Cover Breather Hardware Set. Replaces OEM # 90018-300-000 X2 and OEM # 93500-06050-0A X1.
Steering Stem Bolt and Washer Set
Steering Stem Bolt and Washer Set. Includes 2 Bolts and 2 Washers. Replaces OEM # 92101-10040-0A X2 (Bolts) and OEM # 94102-10000 X2 (Washers).
Clutch Cover Screw Set
Clutch Cover Screw Set of 10 Screws. Replaces OEM # 93500-06028-0A X7 and 93500-06035-0A X3.
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs and 8 Flange Nuts.
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs and 8 Flange Nuts.
Headlight Bucket Case
Black Headlight Bucket / Case, Stock Design - Replaces OEM # 61301-300-020B
Rear Fender Eliminator
Rear Fender Eliminator. Includes holes for custom tail light and license plate install. These are Great for Cafe builds and custom work! If you want a Licence Plate Frame to go with this, Our #73-0087 or 73-0088 fit perfectly, Tailllight #11-2325
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!