Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Exhaust Hardware Set
Exhaust Hardware 10 Piece Set. This Set includes various hard to find hardware needed to install the Stock OEM Type Exhaust. Set Includes: X1 stand stopper rubber C 95011-63000 X1 stand stopper rubber A 95011-63000 X2 pillon step bolt 90146-300-020 X2 nut 94030-12000 X2 flat washer 94102-12000 X2 spring washer 94111-12000 Fits: Stock Type Exhaust on Honda CB750K (1969-76) Note: Exhaust Flange Clamps and Exhaust Pipe Flanges with Hardware are Not Included in this Set, We Sell them Separate.
Shock Absorber Set ~ Stock Design ~ CB750K 1969-71
Stock Type Designed Shock Absorber Set - Chrome Body with Chrome Springs and Black Center. These are modelled after the original stock shocks made for the CB750K 1969-71. The original OEM shocks came with 3 position spring preload adjustments however we have upgraded these to 5 spring preload adjustments so you can better fine tune these shocks! 336mm (13 1/4") Center of Eye to Eye. Stock Match for: Honda CB750K (1969-71) Will Also Fit: Honda CB750K (1972-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic
Rear Brake Rod Assembly
Rear Brake Rod Assembly, Includes Brake Rod, Spring, Brake Arm Joint, Brake Rod Adjusting Nut, Brake Rod Joint Pin and Cotter Pin.
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
CB750K 1971 Speedo & Tachometer Face Plate Set ~ KM/H
Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type. Disassembly of speedometer and tachometer is required. All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards. This face plate set is supplied without jewels. You can re-use the jewels from the faces you replace or we sell those separately.
CB750K 1971 Speedo & Tach Face Decal Set ~ MPH
Speedometer & Tachometer Face Decal (Sticker) Set ~ MPH Type. These decals must be applied over the original gauge face to illuminate. Disassembly of speedometer and tachometer is required. Mounting holes are pre cut to simplify application. Openings for odometer, tripmeter and warning lights must be cut out after application. Removal of original information printed on OEM plastic face is required prior to application of these decals. All decals are "printed" in North America on the highest quality materials.
CB750K 1971 Gas Tank Stripe Decals ~ Gold Stripes
Honda CB750K (1971) Gold Gas Tank Stripe Decals (Stickers) for the Candy Ruby Red, Valley Green Metallic and Candy Garnet Brown models. These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
CB750K 1971 Gas Tank Stripe Decals ~ Black Stripes
Honda CB750K (1971) Black Gas Tank Stripe Decals (Stickers) for the Candy Gold Model. These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
CB750K 1971-72 ~ Warning and Service Label Set
Honda CB750K (1971-72) Warning & Service Label (Sticker) Set. This set includes all warning and service labels that were originally found on these bikes when new. You'll find the quality & accuracy of these decals second to none and accurate in every detail. These reproductions will add the finishing touch to your restoration. This 8 piece warning & service label set includes: 1 - IMPORTANT INFORMATION (tire inflation & info) decal 1 - CAUTION BATTERY warning decal 1 - ENGINE OIL information decal 1 - EXHAUST MODIFICATION warning decal 2 - HELMET HOLDER decals 1 - PRESERVE NATURE (Black) decal 1 - PRESERVE NATURE (White) decal These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Fork Cover Rubber Set
Fork Cover Rubber Set/2, Replaces OEM # 51601-300-000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Master Cylinder Damper Set
Master Cylinder Damper Set. Includes Brake Master Cylinder Rubber Damper, Plate and Washer. This Set is often missing and is used to reduce vibration to the master cylinder lever.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Brake Rod Joint Pin w Cotter Pin
Brake Rod Joint Pin with Cotter Pin, Replaces OEM # 95015-52000 (Joint Pin) and OEM # 94201-16250 (Cotter Pin).
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Throttle Adjusting Spring
Throttle Adjusting Spring, Replaces OEM # 53191-300-000
Starter Clutch Roller Spring
Starter Clutch Roller Spring, Replaces OEM # 28125-516-030 Sold Each, Order the Quantity you Require
Bronze Thrust Bushing Set/2
Bronze Thrust Bushing Set/2. Replace the cheaply made, worn-out factory swingarm bushings with a 2-piece set of brand-new bronze thrust bushings. Replaces OEM # 52109-283-300
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Front Brake Hose Clip
Front Brake Hose Clip, Replaces OEM # 45145-300-020
Ignition Coil Holder Clamp
Ignition Coil Holder Clamp with Bolt, Washer and Nut. This is the clamp that holds the ignition coil in place. Replaces OEM # 30151-300-000 / 30152-300-000
Rear Brake Light Stop Switch Bracket
Rear Brake Light Stop Switch Bracket, Replaces OEM # 50156-300-020
Center Stand Spring Plate
Center Stand Spring Plate, This is the Plate the Center Stand Spring Attaches to. Replaces OEM # 50523-300-010
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Left Side Footrest Return Spring
Left Side Footrest Return Spring. This is the Spring that Allows the Left Side Footpeg to be Lowered and Raised. Replaces OEM # 50644-300-670
Rear Brake Shoe Spring Set/2
Rear Brake Shoe Spring Set of 2. Replaces OEM # 43151-346-000
Neutral Switch Screw
Neutral Switch Screw, This is the small Screw that threads into the Neutral Switch. Replaces OEM # 35752-300-020
Points Cover Screws
Points Cover Screws (Set of 2). Fits: ALL 1969-1978 Honda CB750 Points Covers and Our Points Cover (Part #13-0000).
Muffler Connecting Tube Set
Muffler Connecting Tube Set for the Stock OEM Exhaust System. Includes 1 Tube, 1 Band Clamp and 1 Screw. Replaces OEM # 18472-300-000 (Tube), OEM # 18473-300-000 (Band Clamp), OEM # 93500-05016 (Screw). Note: 2 Sets Used Per Bike, Order the Quantity you Require
Battery Box Rubber Set
Battery Box Rubber Set. Includes Battery Rubber X1, Battery Box Collar X1, Bolt X1 and Washer X1. This set fastens into the top section of the Battery Box. Fits: Honda CB750K (1969-76) - 4 Sets Used Per Bike, CB750K (1977-78) - 3 Sets Used Per Bike, CB750F (1975-76) Supersport - 4 Sets Used Per Bike, CB750F (1977-78) Supersport - 3 Sets Used Per Bike, CB750A (1976-78) Hondamatic - 2 Sets Used Per Bike Note: Order the Quantity of Sets you Require
Battery Box Rubber "A"
Battery Box Rubber "A", Replaces OEM # 50323-300-010 This rubber is fastened into the top section of the Battery Box. Fits: Honda CB750K (1969-76) - 4 Used Per Bike, CB750K (1977-78) - 3 Used Per Bike, CB750F (1975-76) Supersport - 4 Used Per Bike, CB750F (1977-78) Supersport - 3 Used Per Bike, CB750A (1976-78) Hondamatic - 2 Used Per Bike Note: Order the Quantity of Rubbers you Require
Neutral Switch O-Ring
Neutral Switch O-Ring, Size 18x3, Replaces OEM # 91307-035-000 / 91307-KF0-003
Cam Sprocket
Cam Sprocket, Replaces OEM #14321-392-000 / 14321-300-010
Fork Cover Rubber Washer Set
Fork Cover Rubber Washer Set/2. These are the Rubber Washers used between the Fork Cover and the Headlight Bucket.
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Valve Guide Clip
Valve Guide Clip, Replaces OEM # 12211-250-310 Sold Each, Order the Quantity you Require
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Kick Starter Ratchet Spring
Kick Starter Ratchet Spring. This Ratchet Spring Attaches by the Kick Starter Gear. Replaces OEM # 28253-300-000
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Passenger Rear Footpeg Pin & Cotter Pin Set
Passenger Rear Footpeg Pin & Cotter Pin Set. Set Includes 2 Footpeg Pins and 2 Cotter Pins. Replaces OEM # 95015-83000
Seat Hinge Pin with Hardware
Seat Hinge Pin and Hardware Set, Includes 1 Pin, 1 Washer and 1 Attachment Clip. Note: Set Includes Enough for One Hinge, Order the Quantity of Sets you Require
Seat Hinge Set
Seat Hinge Set, This set is a reproduction of the original hinges no longer available from Honda. Set includes Hinge A, Hinge B, 2 Long Pins, 2 Attachment Lock Pins and 2 Washers.
Front Brake Hose Guide
Front Brake Hose Guide, Replaces OEM # 45129-300-000
Carb Overflow Guide
Carb Overflow Guide, Replaces OEM # 11355-300-000