Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included►
- Honda
Clutch Lever Return Spring
Clutch Lever Return Spring. This is the Spring Located Behind the Clutch Cover. Replaces OEM # 22815-300-000
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Rear Sprocket Washer Set
Rear Sprocket Tongued Lock Washer (Pack of 2). Replaces OEM # 94108-17000
Kick Starter Stopper Spring with Steel Ball
Kick Starter Stopper Spring with Steel Ball Set. Replaces OEM # 28333-300-000 (Spring) and OEM # 96211-08000 (Steel Ball).
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45109-300-003
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Starter Motor Bolt (Set/2)
Starter Motor Flange Bolt Set/2. Replaces OEM # 95700-06056-00
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Rear Sprocket Bolt & Nut Set
Rear Sprocket Stud Bolt (12x54) & Nut Set. Set includes 4 Stud Bolts and 4 Nuts. These Stud Bolts Fasten to the Centre Wheel Flange and Rear Sprockets. Replaces OEM # 90128-341-000 X4 (Bolts), 94030-12000 X4 (Nut)
Tail Light Mounting Hardware Set
Tail Light Mounting Hardware Set. This Set is Used to Mount the Tail Light Bracket. This 12pc Set Includes 4pc Tail Light Setting Bolts, 4pc Tail Light Setting Washer and 4pc Rubber Fender Cushion.
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Front Brake Rotor
Front Brake Rotor. Replaces OEM# 45120-392-000 / 45120-300-040 / 45120-341-000
Exhaust Heat Shield with Hardware
Exhaust Heat Shield with Hardware. Includes One Heat Shield for One Muffler and the Hardware required to install it (3 Bolts, 3 Washers, 6 Spacers). Replaces OEM # 18315-300-020 Fits: Stock Type Exhaust on Honda CB750K (1969-76) Note: 2 Heat Shields Required Per Bike, Order the Quantity You Require
Kick Starter Return Spring
Kick Starter Return Spring. Replaces OEM # 28261-300-010
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Spring Set
Clutch Spring Set
Clutch Plate
Clutch Plate 7 Pieces Required .138" Thickness OEM Ref # 22201-300-000 / 22201-371-000
Clutch Plate
Clutch Plate 1 Piece Required .138" Thickness OEM Ref # 22202-371-000 / 22202-390-000 / 22202-392-000
Steel Clutch Plate
Steel Clutch Plate 5 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Carb Holder Set
Carb Holder Set (Set of 4)
Carb Air Box Rubber Boot
Carburetor to Air Box Rubber Boot. Replaces OEM # 17253-341-300 Note: 4 Boots Used Per Bike, Order Quantity you Require
Carb Fuel Line O-Ring Kit
Carb Fuel Line O-Ring 12Pc Kit Includes: 8 Carb Fuel Connector Tube O-Rings and 4 Float Bowl Drain Seal Connector Tube O-Rings (The 4 tubes that connect the 4 carbs together).
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Air Filter Cover O-Rings Pk/2
Air Filter Cover Bolt O-Rings Pk/2, Replaces OEM# 91301-704-000
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-341-004
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).
Ultimate Performance Main Jet Kit
Ultimate Performance Main Jet Kit. Kit includes a total of 44 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #100 (X4), #102 (X4), #105 (X4), #108 (X4), #110 (X4), #112 (X4), #115 (X4), #118 (X4), #120 (X4), #122 (X4) and #125 (X4)
Pilot Jet Set (Pk/4)
Stock Type Pilot Jet Set of 4 (Size #40). Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Fits: Honda CB750K (1972-76) with original stock carbs CB750F (1975-76) with original stock carbs Note: These Pilot Jets (#40) were the standard size equipped from the factory.
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach. Fits: All 92mm (3.6") glass lenses. Sold each, order the quantity you require
Speedometer & Tachometer Crimp Ring Set/2
Speedometer & Tachometer Crimp Ring Set/2. When changing the speedometer or tachometer face plates these rings are often damaged. Get a new set today to have your speedo & tachometer restoration looking perfect! Dimensions: Inner diameter 102.7mm. - Outer diameter 107.5mm.
Speedometer & Tachometer Replacement Glass Lens Set/2
Speedometer & Tachometer 92mm Glass Lens Set/2. If the glass lens of your gauges have scratches or are broken, with these glass lenses you are able to repair your gauges' lenses. These glass lenses are slightly bent like the original glass lenses.
Two Metal Speedo / Tach Gauge Covers With Crimp Rings
Two Metal Speedo / Tach Gauge Covers With Crimp Rings. These metal gauge covers are often dented, scratched and corroded. It takes a lot of time to remove the dents, scratches and repaint the covers. With this set of two reproduction gauge covers, you can recondition your gauges so that these will look like new! These covers are unique and the best quality on the market (Made in the United Kingdom). The black metal covers are already painted in the right semi-gloss black colour and are ready to use. This listing contains two black metal covers with crimp rings. These covers lack the hole at the side for speedo meters with the trip meter reset at the side. This hole must be drilled if required.
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal. This internal rubber seal replaces the ripped, dried or missing rubber internal seal. This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
OEM Type Shock Absorber Bolt
Chrome Shock Absorber Bolt, Replaces OEM # 93201-10032-0B / 93200-10032-0A Note: 2 Bolts Used Per Bike, Order the Quantity you Require
Alternator Cover Mounting Screw Set
Alternator Cover Mounting Screw Set. Set of 8 Mounting Screws Used to Fasten the Main Alternator Cover in place (Not the Alternator Face Plate). Replaces OEM # 93500-06032-OA X7 / 93500-06035-OA X1
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Clutch Cover Screw Set
Clutch Cover Screw Set. Includes all 3 Screws needed to fasten the Clutch Cover. Replaces OEM # 93700-06016-0B X3.