Honda ► CB750L ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750L with universal parts included►
- Honda
Press In Type Pilot Jet Set ~ Size #42 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #42) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #42 which is the oversize for these bikes, please confirm this is the size you require before purchasing.
Idle Slow Circuit Nozzle (Pk/4)
Idle Slow Circuit Nozzle (Pk/4), Replaces OEM # 16166-425-671
High Performance Kibblewhite Valve Spring Set
High Performance Kibblewhite Valve Spring Set of 16. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. The springs in these kits are wound from super clean chrome silicon wire that has been heat treated and shot peened. These components offer optimal fitment, keeping lateral movement to a minimum. They work together as a system, providing long life, and maximum performance.
High Performance Kibblewhite Intake/Exhaust Valve Guide
High Performance Kibblewhite Intake or Exhaust Valve Guide (Standard Size). Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite uses the copper based C63000 nickel-aluminum bronze as a material to make these bronze valve guides because of its ideal characteristics for the application. The 5% nickel content provides superior resistance to wear, and the approximately 80 percent copper content delivers outstanding heat conductivity. Kibblewhite guide profiles are designed to have minimal effect on the airstream while maintaining critical cross sectional thickness in high temperature areas, which promotes high performance and endurance. Sold Each, Order the Quantity you Require
High Performance Kibblewhite Valve Stem Seal Set
High Performance Kibblewhite 100% Viton Valve Stem Seal Set of 16. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite Red 100% Viton valve stem seals are designed to have optimum fitment, allow, maximum lift, and to give maximum life. Kibblewhite Red valve stem seals are resistant to high temperatures, petroleum products and the corrosive gasses that are the by-products of combustion. These viton seals retain their ability to seal in situations where other materials could harden and allow oil to enter the combustion chamber causing detonation, carbon build up and a loss of power. The Red Ones are truly the racers choice.
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Cap (Set/2). These Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-362-000 X2.
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Side Stand Rubber Hardware Set
Side Stand Rubber Hardware Set, Includes Metal Collar and Silver Colored Flange Bolt.
Front Brake Caliper Piston Boot
Front Brake Caliper Piston Rubber Dust Boot, Replaces OEM # 45109-425-003
Carb Bolt Kit
Carburetor Bolt and Washer 43 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Rear Wheel Damper Rubber
Rear Wheel Drive Damper Rubber, Replaces OEM # 41241-300-050 These fit between the rear wheel sprocket hub and the wheel hub and get worn down over time from use. Note: 4 Used Per Bike, Order The Quantity you Require
Custom Black Horn with Bracket ~ Joker Machine
Joker Machine Brand ~ Small Custom Black Horn with CNC Machined Bracket and 2 Gold Mounting Screws. This horn relocates to the center-line of the frame instead of the stock horn's offset position. This custom small horn gives your bike a racy billet look and enables better clearance for steering damper installations. High quality made in the U.S.A.
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Starter Motor
Starter Motor Unit. Replaces OEM # 31200-438-505 This starter bolts on as direct replacements for the OEM type. Features an improved high-output permanent magnet.
Seat Cover
Replacement Seat Cover with Strap (No hardware, strap buckles or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. Each seat cover is made entirely by hand, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam. Fits: the Original Stock Honda CB750L (1979) Limited Seat Only This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Valve Spring Seat (Inner)
Valve Spring Seat (Inner), Replaces OEM # 14776-422-000 Sold Each, Order the Quantity you Require.
Valve Spring Seat (Outer)
Valve Spring Seat (Outer Seat), Replaces OEM # 14775-422-000 Sold Each, Order the Quantity you Require.
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-329-000 Sold Each, Order the Quantity you Require.
Steering Stem Washer
Steering Stem Washer, Replaces OEM # 90503-425-000 Sold Each, order the quantity you require.
Steering Stem Nut
Steering Stem Nut, Replaces OEM # 90304-425-000 Sold Each, we also offer the washer for this nut
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
TC Bros. Forward Controls Kit
TC Bros. Brand Bolt-On Forward Controls Kit. Kit includes a pair of forward controls featuring CNC machined, knurled aluminum pegs. The mounting plates are heavy duty powder coated steel and bolt to your front motor mounts. The spacers are TIG welded to the mounting plates. Everything bolts on using the supplied mounting hardware with no frame modifications. Mounting instructions with pictures are included with each kit. This kit makes long trips much more comfortable due to the fact that your legs are extended forward rather than bent. Great for choppers, bobbers, or even stock bikes. High Quality, Made in the USA. Linkage Kit Not Included, We Sell that part #73-1164
Front Brake Caliper Shaft Boot
Front Brake Caliper Shaft Boot, Replaces OEM# 45133-425-003. These boots often dry up or rip over the years, keep your calipers clean with these new rubber boots. Fits: Honda CB400T (1980) - 4 Used Per Bike, CM400A (1980-81) - 4 Used Per Bike, CM400T (1980-81) - 4 Used Per Bike, CB650 (1979-81) - 4 Used Per Bike, CB650C (1980-81) Custom - 8 Used Per Bike, CB750L (1979) Limited - 4 Used Per Bike, CB750K (1980-81) - 4 Used Per Bike, CB750C (1980-81) Custom - 8 Used Per Bike Sold Each, Order the Quantity you Require
Headlight Stay / Headlight Reflector Bolt
Headlight Stay / Headlight Reflector Bolt, Replaces OEM# 90120-425-000. This is the bolt that the headlight reflectors / reflector base attach to, this bolt fastens through the headlight ears. Sold Each, 2 Used Per Bike
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-375-000 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Rags”. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - 1 1/2" Pipes Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Peanut Plate Fits 219T Cam Chains
Clip Link
Cam Chain Clip Link Peanut Shape Fits 25H Cam Chains
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BS05MH TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BF05M TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Fits 82RH2015
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Roadhawk Grip Set Chrome Plate Ends With Roadhawk Design 5" Inside Length x 7/8"
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/4" Inside Length x 7/8" 150mm Length
Grips
Sportbike Gel Grip Set Closed End Type 5" Inside Length x 7/8" 135mm Length