Honda ► CB900C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB900C with universal parts included that match “honda sl125”►
- Honda
Honda CB Charging Rotor
Honda CB Charging Rotor, Replaces OEM # 31110-426-832 This rotor is a high quality OEM style replacement for Honda field coil rotors. The field coil is wound to stock specifications. This rotor is an easy installation and provides years of trouble free reliability from your Honda engine. Easy bolt-in installation just like the stock rotor.
Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Cotter Valve / Valve Keeper
Cotter Valve / Valve Keeper, Replaces OEM# 14781-107-003 / 14781-107-020. 2 Used For Each Valve Spring. Sold Each, Order the Quantity you Require
Ignition Spark Unit
Aftermarket Ignition Spark Unit for Honda - 2 units required per bike. Replaces Honda OKI or NEC units. Replaces OEM Ref # 30400-MA4-601
CB Black Mirror - Original Type - DOHC
Mirror - Honda Black Type - 8" Stem, 10mm. RH threads. Original Stock Type For: Honda CB750K (1979-82), CB750F (1979-82) Supersport, CB750L (1979) Limited, CB900F (1981-82) Supersport, GL1100 (1981-83) Will also fit Any Honda: CB Note: These Fit Both Left And Right Side Of Bike, Order 2 For A Complete Set
Chrome LTD Type Mirror ~ Short 5" Stem
Mirror - Honda Chrome Ltd. Type - 5" Short Stem, 10mm. RH threads. Note: These Fit Both Left or Right Side Of Bike, Order 2 For A Complete Set
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Seat Cover
Replacement Seat Cover (No hardware or chrome trim included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright.
There is a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam.
Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available.
Comes with complete installation instructions as well as step by step instructions on how to repair damaged seat foam.
Gasket Set (Top End Set Only)
Top End Gasket Set - Fits: Honda CB900C (1980-82) Custom, CB900F (1981-82) Supersport Sets made by Athena of Italy the European original equipment supplier to Yamaha, Honda, Kawasaki, Suzuki and all major Italian bike makers. Top Quality ISO-9000 approved. Set contains: 18-7000 Cylinder Head Gasket, 18-6991 Cylinder Base Gasket, 12-1002 Valve Cover Gasket, 18-7013 Exhaust Headpipe Gasket Pk/4, 18-7066 Camshaft Holder Seal, 18-7067 Cylinder Sleeve O-Rings Pk/4, valve stem seals, Various O-Rings.
CB900C 1982 Decal Set ~ Candy Empire Blue & Candy Blue Models
Honda CB900C (1982) Custom 5 Pc. Bike Decal (Sticker) Set for the Candy Empire Blue & Candy Blue Models. Fuel tank stripes must be overlapped to join. These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Sintered Brake Pads
Rear Brake Pads Pk/2 Sintered Pads OEM Ref # 43105-MA3-007
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Rear Brake Caliper Piston
Rear Brake Caliper Piston (1) - 42.8mm Diameter x 41mm Length - OEM Ref # 45107-415-006
Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-438-007
Front Brake Caliper Bolt Set
Front Brake Caliper Bolt Set, Replaces OEM# 90123-371-000. Each set includes 2 bolts and 2 washers - enough for either the left or right caliper. If you would like bolts for both sides purchase 2 sets.
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Rear Brake Master Cylinder Repair Kit
Rear Brake Master Cylinder Repair Kit OEM Ref # 43520-422-305
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Speedometer Cable
Speedometer Cable - OEM Ref # 44830-461-770 - Length 42.5" Made in Japan
Stop Switch Assembly
Stop Switch Assembly with Spring, Replaces OEM# 35350-166-005
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-329-000 Sold Each, Order the Quantity you Require.
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Brake Caliper Piston
Brake Caliper Piston - Front 30mm x 35mm OEM Ref # 45107-MA3-006
Piston Kit (Standard Size)
Standard Size Piston (64.5mm) with Piston Pin, Piston Pin Clips (pr.) and Piston Rings. Piston OEM Ref. # 13101-438-000 (Std.) Note:This Kit includes piston, piston pin, clips and piston rings to rebuild one piston. 4 Kits are needed to rebuild all pistons.
Stop Light Switch
Front Stop Light Switch OEM Ref # 35340-MA5-671 / 35340-MM5-600 / 35340-ML7-000
Cam Chain Tensioner Spring "B"
Cam Chain Tensioner Spring "B". This is the Cam Chain Tensioner Spring for the Smaller Cam Chain Tensioner ("B"). Replaces OEM # 14538-425-000
Intake Valve
Intake Valve - Replaces OEM # 14711-MB0-000 / 14711-MB2-000 / 14711-438-000 Made in Japan
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Front Brake Caliper Piston Sealing Ring
Front Brake Caliper Piston Sealing Ring, Replaces OEM # 45108-300-003
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Brake Lever
Brake Lever OEM Ref # 53175-438-000 / 53175-438-010 / 53175-422-000
Clutch Adjuster Bolt
Clutch Adjuster Bolt, Replaces OEM# 22841-425-000
Clutch Spring Kit
Clutch Spring Kit. Note: There will be extra springs in this kit for some bikes.
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
Brake Caliper Piston
Brake Caliper Piston - Rear 30mm x 35mm OEM Ref # 45107-MA3-006
Side Stand Rubber Hardware Set
Side Stand Rubber Hardware Set, Includes Metal Collar and Silver Colored Flange Bolt.
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Starter Relay Pigtail / Plug
Starter Relay Pigtail / Plug Connects to our starter relays #24-2004, 24-2157 and 73-0824. Despite wire colors you must confirm wire orientation before hooking up!
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Speedo/Tachometer Meter Cushion
Speedo/Tachometer Meter Cushion, Replaces OEM # 37235-323-700