Honda ► CB900F ►
-
Here’s our hand-picked list of clutch parts for your Honda CB900F with universal parts included that match “honda sl125”►
- Honda
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Clutch Adjuster Bolt
Clutch Adjuster Bolt, Replaces OEM# 22841-425-000
Clutch Spring Kit
Clutch Spring Kit. Note: There will be extra springs in this kit for some bikes.
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-425-000 / 22202-MT8-000
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-KAE-000 / 22201-KM4-000 / 22201-KA4-711 / 22201-KA4-712 / 22201-KZ3-730 / 22201-MAE-000 / 22201-MAL-600 / 22201-MR7-000 / 22201-MS6-620 / 22201-MV4-000
Steel Clutch Plate
Steel Clutch Plate, Replaces OEM# 22321-MAS-000 Sold Each, Order The Quantity you Require
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-MV8-920 / 13088-1085
Clutch Cable
Clutch Cable - OEM Ref. # 22870-425-010 / 22870-ME1-670
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Clutch Cover Gasket
Clutch Cover Gasket - OEM Ref # 11396-425-000
Steel Clutch Plate "B" ~ Riveted Plate
Steel Clutch Drive Plate "B" - OEM Ref # 22322-425-000 This is the thick double steel plate with rivets in it. It is an essential part of any clutch rebuild as the rivets are known to wear over time. 1PC Required per Bike
Clutch Spring Bolt Set
Clutch Spring Bolt Set of 6. Replaces OEM # 95725-06025-00 X6.
Clutch Lever
Clutch Lever OEM Ref # 53178-425-003 / 53178-461-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Handlebar Rubber Boot
Handlebar Rubber Boot. Replaces OEM # 53180-425-010
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Clutch Lever
Clutch Lever OEM Ref # 53178-KVO-000
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Valve Shim Tool
Valve Shim Tool Honda CBX, CB750/900
Oil Filter Wrench
Oil Filter Wrench Wafer-Thin For GL1500 Goldwings Also Works On Many other Honda/Yamaha/Kawasaki Models
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
Brake & Clutch Lever Assemblies ~ Silver
Brake & Clutch Lever Assemblies ~ Silver. Includes both the clutch and brake levers and both perches (brackets). Styled after the Honda Stock type controls. These are universal for 7/8" bars, and are great for custom projects. One piece brackets with 10mm RH Thread mirror mount holes. The lever perch accepts the factory style brake switch. Note: Make sure you have 7/8" handelbars and you are using a cable operated clutch and front brake. This is a universal part and some mods may have to be made to work with your bike.
Brake & Clutch Lever Assemblies ~ Black
Brake & Clutch Lever Assemblies ~ Black. Includes both the clutch and brake levers and both perches (brackets). Styled after the Honda Stock type controls. These are universal for 7/8" bars, and are great for custom projects. One piece brackets with 10mm RH Thread mirror mount holes. The lever perch accepts the factory style brake switch. Note: Make sure you have 7/8" handelbars and you are using a cable operated clutch and front brake. This is a universal part and some mods may have to be made to work with your bike.