Honda ► CB900F ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB900F►
- Honda
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-443-762
Brake Pads
Rear Brake Pads Pk/2 OEM Ref # 43105-MA3-007
Sintered Brake Pads
Rear Brake Pads Pk/2 Sintered Pads OEM Ref # 43105-MA3-007
Cam Chain Tensioner Spring "A"
Cam Chain Tensioner Spring "A". This is the Cam Chain Tensioner Spring for the Larger Main Cam Chain Tensioner ("A"). Replaces OEM # 14514-425-010
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Steering Stem Head Lock Nut
Steering Stem Head Top, Thread on Lock Nut. Replaces OEM # 90302-425-830
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Brake Rod Pin
Brake Rod Pin, Replaces OEM# 46503-371-000
Clutch Adjuster Bolt
Clutch Adjuster Bolt, Replaces OEM# 22841-425-000
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22202-425-000 / 22202-MT8-000
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Steel Clutch Plate "B" ~ Riveted Plate
Steel Clutch Drive Plate "B" - OEM Ref # 22322-425-000 This is the thick double steel plate with rivets in it. It is an essential part of any clutch rebuild as the rivets are known to wear over time. 1PC Required per Bike
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Clutch Spring Kit
Clutch Spring Kit. Note: There will be extra springs in this kit for some bikes.
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Holder Set
Carb Holder Set (Set of 4) - Replace those old cracked or dried up carb holders with a brand new set! Replaces OEM# 16211-438-000 , 16212-438-000 , 16213-438-000 , 16214-438-000 If you require band clamps, these carb holders require our 46-49mm diameter clamps part #15-0685 X4 and 50-52mm diameter clamps #15-0689 X4.
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Performance Main Jet Kit
Performance Main Jet Kit. Kit includes a total of 16 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #105 (X4), #110 (X4), #115 (X4) and #120 (X4).
Ultimate Performance Main Jet Kit
Ultimate Performance Main Jet Kit. Kit includes a total of 44 Main Jets for Keihin Carbs. Use this jet kit to unleash the extra power you should have from your aftermarket exhaust, flee flowing air filters or any engine mods you have made. Kit includes Main Jets #100 (X4), #102 (X4), #105 (X4), #108 (X4), #110 (X4), #112 (X4), #115 (X4), #118 (X4), #120 (X4), #122 (X4) and #125 (X4)
Pilot Jet Set/4
Stock Type Pilot Jet Set of 4 (Size #35). Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Note: These Pilot Jets (#35) were the standard size equipped from the factory
Rubber Passage Plug
Rubber Passage Plug Pk/5 OEM Ref # 16010-425-671 / 16010-461-781 / 16010-469-004
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-413-751 / 16155-397-971
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Air Cut Off Valve With Cover
Carb Air Cut Off Valve with Cover - OEM # 16048-429-771 (Diaphragm), 16048-425-771 (Spring + 1 O-Ring), 16048-429-771 (Cover).
Float Bowl Screws Pk/2
Float Bowl Screws with Lock Washers, Pack of 2 Screws and 2 Washers. These fasten the float bowl in place. Replaces OEM # 93892-04016-00 Order Quantity of Screws you Require
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Speedo/Tach Cap Nut Set/4
Set of 4 Cap Nuts Used to Mount the Stock OEM Type Speedometer and Tachometer. Replaces OEM # 94021-06020 X4.
NGK Spark Plug
NGK DR8EA Spark Plug
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.
Clutch Cable
Clutch Cable - OEM Ref. # 22870-425-010 / 22870-ME1-670
Speedometer Cable
Speedometer Cable - Black - OEM Ref # 44830-KB4-700 / 44830-356-010 Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-149-000 (700mm), 37260-KB7-010 / 37250-149-000 Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref # 37260-KB7-010 / 37260-438-000 Made in Japan Length is 24" - Confirm this is the length you require before purchasing
Throttle Cable - Push
Throttle Cable "Push Type" - OEM Ref. # 17920-425-030
Throttle Cable - Pull
Throttle Cable "Pull Type" - OEM Ref. # 17910-425-020 / 17910-425-030 / 17910-425-405 Made in Japan
Choke Cable
Choke Cable - Black - OEM Ref. # 17950-425-000 Made in Japan
Chrome Spark Advancer Cover
Spark Advancer Cover ~ Chrome ~ Replaces OEM # 30371-425-010 These covers are often dented, rusted or worn. A new chrome cover really adds to the look of your bike!
Oil Passage Cap with O-Ring
Oil Passage Cap with O-Ring. Replaces OEM # 15331-300-000 (Oil Passage Cap) and OEM # 94608-40000 (O-Ring). Note: Sold Each, Order the Quantity of Caps you Require
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. Replaces OEM # 45522-422-000
Handlebar Rubber Boot
Handlebar Rubber Boot. Replaces OEM # 53180-425-010
DOHC Screw Set
71PC DOHC Screw Set, Includes Front Stay Plate Screws (8), CV Cap Screws (8), Throttle Cable Bracket Screw (1), Rear Stay Plate Screws (8), Vacuum Petcock Screws (6), Bowl Screws (12), Accelerator Pump Cover Screws (3), Air Cutoff Screws (8), Choke Cable Clamp Screw (1), Throttle Plate Screws (8) and Choke Plate Screws (8).