Honda ► CBR900RR ►
-
Here’s our hand-picked list of electrical parts for your Honda CBR900RR with universal parts included►
- Honda
H7 Bulb
H7 Bulb, 12Volt 55Watt PX26D, Replaces OEM# 34901-MAT-611 , 92069-0053 , 5PS-84314-00-00
Signal Stem
Front Signal Stem OEM Ref # 33691-MB2-000 / 33691-MB2-009 / 33691-MJ0-003 / 33691-MB3-003 / 33491-MJ0-003
Signal Stem
Rear Signal Stem OEM Ref # 33691-MB2-000 / 33691-MB2-009 / 33691-MJ0-003 / 33691-MB3-003 / 33491-MJ0-003
Starter Relay Pigtail / Plug
Starter Relay Pigtail / Plug Connects to our starter relays #24-2004, 24-2157 and 73-0824. Despite wire colors you must confirm wire orientation before hooking up!
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front o& Rear OEM Ref # 33406-MB2-601 / 33406-MB2-671
Turn Signal Lamp
Turn Signal Lamp - Glossy Black 3 Wire - Dual Filament Left Front / Right Rear * For Single Filament, Use 2 of 3 Wire *
Turn Signal Lamp
Turn Signal Lamp - Glossy Black 3 Wire - Dual Filament Right Front / Left Rear * For Single Filament, Use 2 of 3 Wire *
Front Stoplight Switch
Front Stoplight Switch OEM Ref # 35340-MM5-600
Alternator Cover Gasket
Alternator Cover Gasket OEM Ref # 11392-MV9-670
Turn Signal Flasher Relay
Turn Signal Flasher Relay, Replaces OEM# 38301-MG9-681 / 38301-KK9-952 / 38301-KK9-951 / 38301-MF8-773 / 38301-MF8-772 / 38301-MB0-004 / 38301-MG9-671.
Ignition Coil
Ignition Coil, Replaces OEM # 30510-KT7-023 Dual Output, 12 Volt, 2.20 Ohm Coil
Starter Relay
Starter Relay, Replaces OEM # 38501-GN2-014
Radiator Fan Switch
Radiator Fan Switch, Replaces OEM # 37760-MR1-003 / 37760-MT2-003
Rectifier Regulator
Rectifier Regulator No Wires - 5 Prong Socket OEM Ref # 31600-MV4-000 / 31600-MV4-010 / 31600-KY2-703
Alternator Stator
Alternator Stator OEM Ref # 31120-MAS-004
Starter Brush Set
Set of 4 replacement starter brushes. Includes 2X brushes for replacing on the terminal brush set OEM# 31201-MR6-008 and 2X brushes for replacing the brushes on the brush holder set OEM# 31206-MR6-008. 6 x 10 x 13mm Permanent magnet brush starters, 2X (+) insulated lead and 2X (-) non insulated lead brushes.
Rectifier Regulator
Rectifier Regulator OEM Ref # 31600-MCJ-641
Alternator Stator
Alternator Stator OEM Ref # 31120-MW0-004 / 31120-MAT-004
Starter Relay
Starter Relay OEM Ref # 35850-MR5-007
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Neutral Switch
Neutral Switch, Replaces OEM # 35600-KE8-003
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-15001 Band Overall Size: 5.25" (133mm) Measuring from the inside of the brackets.
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Black Universal Adjustable Headlight Brackets
Universal Adjustable Headlight Bracket Set/2 - Black Finish. Fits: 35-41mm Forks
Replacement Sealed Beam 12V (5 3/4")
Replacement Sealed Beam 12 Volt 60/37W 5 3/4" Universal Sealed Beam - DOT & CHP Approved
Replacement Sealed Beam 12V (7")
Replacement Sealed Beam 12 Volt 60/50W 7" Universal Sealed Beam
Headlamp Visor (7")
Headlamp Visor With Eagle Emblem Fits 7" Headlight
Tommaselli Type Headlight Brackets (35mm-36mm)
Tommaselli Type Headlight Brackets 35-36mm
Headlight Bracket Set
Headlight Bracket Set - Chrome 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Tommaselli Type Headlight Brackets (32mm-34mm)
Tommaselli Type Headlight Brackets 32-34mm
Headlight Bracket Set (35mm)
Aluminum Custom Headlight Brackets 35mm Headlight Mounting Holes 7/16"
Headlight Bracket Set
Headlight Bracket Set - Black 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Cast Aluminum Black Headlight Bracket Set
Cast Aluminum Black Headlamp Mounting Bracket Set. Sold with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters.
Custom Universal Headlamp
Custom Universal Headlamp 4 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Custom Universal Headlamp
Custom Universal Headlamp 5 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Rectangular Headlamp
Small Rectangular Headlamp 6.5"x4.5" Lens Steel Lens Frame, With Black Plastic Housing Halogen Bulb & Headlamp Plug With Wires Side Mount, 14mm Mounting Holes, 7.25" Width Two Openings On Back
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Headlight Shell & Rim
Custom Ready to Assemble Chrome Side Mount Headlight Bucket Rim & Retainer. Designed for 7" sealed or non sealed H4 type headlights. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Comes with a wired plug that works with sealed beam or H4 bulbs. H4 Beam Headlight sold separately #09-0072
Headlight Assembly
Chrome 7" Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. H4 Bulb with European style parking light (Not used for North American models)
Classic Round Black Taillight
Classic Round Black Taillight with plate bracket. 2 1/4" Round lens (with a clear bottom to light up your plates), 12 Volt double filament bulb. Works as a running and brake light.