Honda ► CBX1050 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CBX1050►
- Honda
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
OEM Type Shock Absorber Bolt
Chrome Shock Absorber Bolt, Replaces OEM # 93201-10032-0B / 93200-10032-0A Note: 2 Bolts Used Per Bike, Order the Quantity you Require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Speedometer Cable
Speedometer Cable - Black - OEM Ref # 44830-KB4-700 / 44830-356-010 Made in Japan
OEM Type Gas/Fuel Tank Cap
OEM Type Gas/Fuel Tank Cap with Gasket and 2 Keys. Replaces OEM # 17620-460-067
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. Replaces OEM # 45522-422-000
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Primary Chain
OEM Quality Primary Chain, 58 Link. Replaces OEM # 23131-422-004
Carb Holder Set
Carb Holder Set of 6, Replaces OEM # 16211-422-000
Carb Holder Set
Carb Holder Set of 6, Replaces OEM # 16211-MA2-000
Valve Shim Kit
20 Piece Valve Shim Kit with Plastic Case, 25mm Diameter Valve Shims. Includes 2 of each of the following sizes. 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00, 3.10.
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Rear Brake Light Stop Switch Spring
Rear Brake Light Stop Switch Spring. This is the Spring that Attaches to the Rear Stop Light Switch. Replaces OEM # 35357-358-000
Tail Light Lens Screws
Tail Light Lens Screws, Set of 4. Replaces OEM # 90147-147-671
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 43353-548-003
Air Sensor Sub Wire with Rubber
Air Sensor Sub Wire with Rubber Cover, this is the wire that connects to and covers the air sensor. Replaces OEM # 32111-463-000
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17632-176-771
Fork Seal Stopper Metal Ring Pk/2
Fork Seal Stopper Metal Ring Pk/2, Replaces OEM # 51447-KL4-951 This is the Metal Ring above the Fork Seal.
Carburetor Needle Jet Holder
Carburetor Needle Jet Holder, Replaces OEM # 16165-422-004 Note: Sold Each
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Pilot Jet Set ~ Size #35 (Pk/4)
Pilot Jet Set of 4 (Size #35), Replaces OEM # 99103-GY6-0350 Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible.
High Performance Kibblewhite Intake/Exhaust Valve Guide
High Performance Kibblewhite Intake or Exhaust Valve Guide (Standard Size). Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite uses the copper based C63000 nickel-aluminum bronze as a material to make these bronze valve guides because of its ideal characteristics for the application. The 5% nickel content provides superior resistance to wear, and the approximately 80 percent copper content delivers outstanding heat conductivity. Kibblewhite guide profiles are designed to have minimal effect on the airstream while maintaining critical cross sectional thickness in high temperature areas, which promotes high performance and endurance. Sold Each, Order the Quantity you Require
Piston Ring Set (Standard Size)
Standard Size Piston Ring Set Ring Set OEM Ref # 13011-438-004 (Std.) Japanese made Superior Quality Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Cap (Set/2). These Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-362-000 X2.
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights
Valve Spring Seat (Inner)
Valve Spring Seat (Inner), Replaces OEM # 14776-422-000 Sold Each, Order the Quantity you Require.
Valve Spring Seat (Outer)
Valve Spring Seat (Outer Seat), Replaces OEM # 14775-422-000 Sold Each, Order the Quantity you Require.
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-329-000 Sold Each, Order the Quantity you Require.
Swing Arm Pivot Bolt Lock Nut and Washer
Swing Arm Pivot Bolt Lock Nut and Lock Nut Washer, Replaces OEM # 90354-425-830 (Nut), 90600-425-830 (Washer)
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Headlight Reflector Rubber Base
Headlight Reflector Rubber Base, Replaces OEM# 33743-425-600 This is the rubber base that the headlight reflector attaches to. Sold Each, order the quantity you require