Honda ► CL175K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL175K►
- Honda

Sidecover Damper Rubber A
Rubber Sidecover Damper A, Replaces OEM # 17247-303-000

Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires

Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700

Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671

Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671

Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!

Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase

Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670

Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033

Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003

Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Nut Thread Inside Diameter is 14.5mm, 1.5 Pitch. Note: Please Check that the Nut Thread Diameter Listed Above is Correct for your Bikes Tank Before Ordering.

Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.

Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.

Steel Clutch Plate
Steel Clutch Plate A OEM Ref # 23311-200-000 Order the Quantity you require

Chrome Exhaust Clamp
Chrome Exhaust Clamp, 14 Fin Type, Center to Centre Mounting Hole Diameter 55mm apart. Replaces OEM # 18231-323-000 / 18231-323-010

Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000

Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-110-000

Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000

Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001

Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require

Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).

Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.

Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Bulb. Replaces OEM # 33701-341-671 / 33701-341-910 / 33701-342-671 Two Bolt Back Mounting Bolt Pattern (Approx 4" Center to Center), 3 Wires, Ready to Mount to your Bike!

Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. Body Length 26mm, Thread 21mm, Total Length 47mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase

Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase

Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000

Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200