Honda ► CL350 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL350 with universal parts included►
- Honda
![Honda CL350 Honda OEM Type Grips](/images/parts/100/02-2424.jpg)
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 95011-14100 / 95011-14200
![Honda CL350 Gear Change Rubber](/images/parts/100/02-2478.jpg)
Gear Change Rubber
Gear Change Rubber OEM Ref # 95011-400-000
![Honda CL350 Seat Rubber "B"](/images/parts/100/02-6533.jpg)
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
![Honda CL350 Starter Motor Seal](/images/parts/100/03-0784.jpg)
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
![Honda CL350 Piston Pin Clips](/images/parts/100/05-7201.jpg)
Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000
![Honda CL350 Cam Roller Pin](/images/parts/100/05-8001.jpg)
Cam Roller Pin
Cam Roller Pin - Replaces OEM # 14605-286-020
![Honda CL350 Cam Shaft Roller Collar](/images/parts/100/05-8002.jpg)
Cam Shaft Roller Collar
Cam Shaft Roller Collar - Replaces OEM # 14606-286-000
![Honda CL350 Cam Chain Guide Pin](/images/parts/100/05-8006.jpg)
Cam Chain Guide Pin
Cam Chain Guide Pin OEM Ref # 14612-286-000
![Honda CL350 Gas Tank Cap](/images/parts/100/07-4647.jpg)
Gas Tank Cap
Chrome Cap Gas Tank Cap with Gasket Installed, Replaces OEM# 17620-402-000 , 17620-402-010
![Honda CL350 Clutch Lever ~ GP Style](/images/parts/100/08-0080.jpg)
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
![Honda CL350 Turn Signal Lamp Gasket](/images/parts/100/11-2085.jpg)
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
![Honda CL350 Turn Signal Replacement Lens](/images/parts/100/11-2110.jpg)
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
![Honda CL350 Tail Light Assembly](/images/parts/100/11-2147.jpg)
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
![Honda CL350 Turn Signal Stem](/images/parts/100/11-2167.jpg)
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
![Honda CL350 Tail Light Lens Gasket](/images/parts/100/11-2168.jpg)
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
![Honda CL350 Tail Light Lens](/images/parts/100/11-2252.jpg)
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
![Honda CL350 Black Steering Stem Nut ~ Joker Machine](/images/parts/100/12-0073.jpg)
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
![Honda CL350 Joker Machine Magnetic Oil Drain Plug](/images/parts/100/12-0108.jpg)
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
![Honda CL350 Rear Fuel Tank Holder Rubber](/images/parts/100/12-0133.jpg)
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM# 17613-286-000
![Honda CL350 Contact Point ~ Right Side](/images/parts/100/14-0005.jpg)
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
![Honda CL350 Contact Point ~ Left Side](/images/parts/100/14-0006.jpg)
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
![Honda CL350 Exhaust Gasket (Each)](/images/parts/100/17-2811.jpg)
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
![Honda CL350 Exhaust Gasket Pk/10](/images/parts/100/17-3811.jpg)
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-286-000 / 18291-286-306
![Honda CL350 Ignition Coil](/images/parts/100/17-6923.jpg)
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
![Honda CL350 Carb Float](/images/parts/100/20-6500.jpg)
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
![Honda CL350 Performance Rotor](/images/parts/100/24-2036.jpg)
Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.
![Honda CL350 Hot Shot Rectifier / Regulator](/images/parts/100/24-2089.jpg)
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
![Honda CL350 Side Cover Emblem](/images/parts/100/27-1000.jpg)
Side Cover Emblem
Side Cover Emblem with 2 Attachment Clips. This Emblem Came in Many Different Color Combos. This is the Black Number/White Background Version. It Will Replace Any of the Other Versions. Replaces OEM# 87128-287-010 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
![Honda CL350 Rear Shock Swingarm Bushing](/images/parts/100/28-6918.jpg)
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
![Honda CL350 Fuel Petcock](/images/parts/100/29-0542.jpg)
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
![Honda CL350 Rear Brake Shoes](/images/parts/100/29-3120.jpg)
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 159mm Width: 30mm OEM Ref # 43120-KG4-006
![Honda CL350 Special Oil Filter Rotor Washer](/images/parts/100/29-7034A.jpg)
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
![Honda CL350 Clutch Center Nut Removal Tool](/images/parts/100/35-0051.jpg)
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
![Honda CL350 Clutch Center Nut Removal Tool ~ Premium](/images/parts/100/35-0076.jpg)
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
![Honda CL350 Clutch Plate](/images/parts/100/39-1079C.jpg)
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
![Honda CL350 Steel Clutch Plate](/images/parts/100/39-1140.jpg)
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
![Honda CL350 Steel Clutch Plate "A"](/images/parts/100/39-1410.jpg)
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
![Honda CL350 Carburetor Screw Kit](/images/parts/100/48-0795.jpg)
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
![Honda CL350 Float Bowl Drain Screw](/images/parts/100/48-5041.jpg)
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
![Honda CL350 Air Screw Needle O-Ring](/images/parts/100/48-5043.jpg)
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
![Honda CL350 Front Sprocket Lock Plate Set](/images/parts/100/49-0782.jpg)
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
![Honda CL350 Steering Stem Washer](/images/parts/100/49-0787.jpg)
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
![Honda CL350 Side Stand Spring](/images/parts/100/49-0788.jpg)
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402