Honda ► CL450 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL450►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 95011-14100 / 95011-14200
Gear Change Rubber
Gear Change Rubber OEM Ref # 95011-400-000
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Front Fuel Tank Holder Rubber
Front Fuel Tank Holder Rubber - Replaces OEM # 17611-283-010 Sold Each.
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM # 17613-292-000
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Starter / Horn Button
Starter / Horn Button
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Gear Change Lever
Gear Change Lever Universal Fit
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Carb Float
Carb Float with Pin, Replaces OEM # 16013-283-004 Note: Sold Each, Order Quantity of Floats your Bike Requires.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Nut Thread Inside Diameter is 14.5mm, 1.5 Pitch. Note: Please Check that the Nut Thread Diameter Listed Above is Correct for your Bikes Tank Before Ordering.
Fork Seals
Fork Seal Set - 35 x 46 x 11. Made In Japan by OEM supplier. Replaces OEM # 91255-292-003
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 52108-457-300 Note: These Replace the factory plastic OEM Type Bushings.
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-000
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.
Cam Chain
Cam Chain 219T x 128 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-283-003 / 94500-02128
Clymer Service Manual
Clymer Service Manual. Clymer motorcycle repair manuals are written specifically for the do-it-yourself enthusiast. From basic maintenance to troubleshooting to complete overhaul, Clymer manuals provide the information you need. Includes Color Wiring Diagrams
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 40 Spokes with 40 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-110-000
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Bronze Thrust Bushing Set/2
Bronze Thrust Bushing Set/2. Replace the cheaply made, worn-out factory swingarm bushings with a 2-piece set of brand-new bronze thrust bushings. Replaces OEM # 52109-283-300
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Passenger Rear Footpeg Pin & Cotter Pin Set
Passenger Rear Footpeg Pin & Cotter Pin Set. Set Includes 2 Footpeg Pins and 2 Cotter Pins. Replaces OEM # 95015-83000
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Custom Drive Chain Adjuster Screws ~ Silver ~ Joker Machine
Joker Machine Brand ~ Silver Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. Body Length 26mm, Thread 21mm, Total Length 47mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase