Honda ► CL450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL450K►
- Honda

Gas/Fuel Tank Cap Latch Assembly ~ Black
Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch with Return Spring, Latch Mounting Pin and C-Clip.

Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 135mm Length. Replaces OEM #' 53165-342-670 / 53166-342-670

Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 95011-14100 / 95011-14200

Footrest Rubbers
Footrest Rubbers Pk/2 OEM Ref # 50661-310-000 / 50661-312-000

Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires

Front Fuel Tank Holder Rubber
Front Fuel Tank Holder Rubber - Replaces OEM # 17611-283-010 Sold Each.

Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.

Matte Black ~ OEM Type Gas/Fuel Tank Cap With Latch Assembly
Matte Black OEM Type Gas/Fuel Tank Cap with Gasket, Hinge Pin (with E-Clip which Allows for easy installation) and Gas/Fuel Tank Cap Latch Assembly, Includes Latch, Return Spring, Latch Mounting Pin and C-Clip. Replaces OEM # 17510-323-310

Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670

Brake Lever
Brake Lever OEM Ref # 53170-216-670 / 53175-286-000 / 53170-286-670 / 53170-329-010 / 53170-369-700 / 53175-369-700

Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700

Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671

Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671

Turn Signal Lamp
Turn Signal Lamp - Front or Rear 2 Wire - 12 Volt Stem *Our Part Number 11-2167*

Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!

Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671

Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase

Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671

Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671

Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670

Stock Type Front Reflector Rubber Base
Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670

Rear Signal Lamp Stay
Rear Signal Lamp Stay - Chrome Rear type - OEM Ref # 33441-369-000 125mm Long.

Custom Fork Boot Collars ~ Joker Machine
Joker Machine Brand ~ Custom Fully CNC Machined Fork Boot Collar Set/2. A great solution for giving your stock bike (with the sheet metal headlight ears), an open fork tube Cafe look, while giving you an upper attachment point in order to retain your stock accordion style O.E.M. fork Gaitors. Designed to fit easily onto 35MM fork tubes and may be adjusted up-or-down along the tube into position, then tightened into place with the recessed set screw located in the groove (totally invisible).

Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033

Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-283-010 / 18291-ME9-000 / 18291-MM8-880

Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.

Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product #P400210850450

Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310

Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.

Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003

Carb Float
Carb Float with Pin, Replaces OEM # 16013-283-004 Note: Sold Each, Order Quantity of Floats your Bike Requires.

Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Nut Thread Inside Diameter is 14.5mm, 1.5 Pitch. Note: Please Check that the Nut Thread Diameter Listed Above is Correct for your Bikes Tank Before Ordering.

Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.

Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000

Fork Seals
Fork Seal Set - 35 x 46 x 11. Made In Japan by OEM supplier. Replaces OEM # 91255-292-003

Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine

Fork Spacer Trim Set
Chrome Front Fork Spacer Trim Set/2. These are the Chrome Ribs that Cover the Top of the Fork Boots. Replaces OEM # 51608-300-000

Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100

Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).

Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2

Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22201-283-000 / 22201-MA7-000

Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685

Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-000

Side Cover Emblem
Cast Metal Side Cover Emblem with the 3 Attachment Clips for the rear of the emblem (Your must use your old bolt and washers that attach at the front of the emblem). Replaces OEM # 87130-294-010 / 87130-319-671 / 87125-346-670 Note: There are a few different styles of side cover emblems used on these bikes. Be sure to verify this design is the type you need before purchasing. Note: 2 Emblems Used Per Bike, Order the Quantity you Require

Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm