Honda ► CX500D ►
-
Here’s our hand-picked list of electrical parts for your Honda CX500D with universal parts included►
- Honda
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Headlamp Rim & Retainer
Headlamp Rim & Retainer Assembly - OEM Ref. # 33101-404-671 / 33101-300-673 / 33101-405-671 / 33100-371-980
7" Halogen Lamp Conversion Kit
7” Halogen Lamp unit with 12v 60/55 Bulb (P43T base) and Bulb Dust Boot for North American Market RH side Drive.
Headlamp Rim
Headlamp Rim - Chrome - Replaces OEM # 33101-300-673 / 33101-405-671
7" Halogen Lamp Conversion Kit
7" Halogen Lamp with 60/55 watt H4 P43T Halogen Bulb and parking light. E-Mark certified for RH drive European Market use (can also be used in North America). Replaces stock sealed beam and fits into stock retainer. Fits: All Honda CB750's (1969-78)
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33406-377-671
Turn Signal Replacement Lens ~ Clear
Turn Signal Replacement Lens - Clear - Front or Rear OEM Ref # 4H7-83312-00
Turn Signal Replacement Lens ~ Smoked
Turn Signal Replacement Lens - Smoked - Front or Rear OEM Ref # 4H7-83312-00
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 4H7-83312-00
Ignition Switch Assembly
Ignition Switch Assembly OEM Ref # 34100-431-017 / 34100-431-027 / 34100-431-037 / 34100-431-047 / 35100-415-017 / 35100-MB9-010
Starter Clutch Repair Kit
Starter Clutch Repair Kit
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Rear Turn Signal Rubbers Pk/2
Rear Turn Signal Rubbers Pk/2, Replaces OEM # 33606-371-000 These are the Rubbers that Go Under the Rear Turn Signal Stays.
Starter Clutch Roller Spring
Starter Clutch Roller Spring, Replaces OEM # 28125-516-030 Sold Each, Order the Quantity you Require
Battery Box Rubber "B"
Battery Box Rubber "B", Replaces OEM # 50327-300-000 Sold Each, Order the Quantity you Require
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Black Universal Adjustable Headlight Brackets
Universal Adjustable Headlight Bracket Set/2 - Black Finish. Fits: 35-41mm Forks
Replacement Sealed Beam 12V (5 3/4")
Replacement Sealed Beam 12 Volt 60/37W 5 3/4" Universal Sealed Beam - DOT & CHP Approved
Replacement Sealed Beam 12V (7")
Replacement Sealed Beam 12 Volt 60/50W 7" Universal Sealed Beam
Headlamp Visor (7")
Headlamp Visor With Eagle Emblem Fits 7" Headlight
Tommaselli Type Headlight Brackets (35mm-36mm)
Tommaselli Type Headlight Brackets 35-36mm
Headlight Bracket Set
Headlight Bracket Set - Chrome 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Tommaselli Type Headlight Brackets (32mm-34mm)
Tommaselli Type Headlight Brackets 32-34mm
Headlight Bracket Set (35mm)
Aluminum Custom Headlight Brackets 35mm Headlight Mounting Holes 7/16"
Headlight Bracket Set
Headlight Bracket Set - Black 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Cast Aluminum Black Headlight Bracket Set
Cast Aluminum Black Headlamp Mounting Bracket Set. Sold with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters.
Custom Universal Headlamp
Custom Universal Headlamp 4 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Custom Universal Headlamp
Custom Universal Headlamp 5 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Rectangular Headlamp
Small Rectangular Headlamp 6.5"x4.5" Lens Steel Lens Frame, With Black Plastic Housing Halogen Bulb & Headlamp Plug With Wires Side Mount, 14mm Mounting Holes, 7.25" Width Two Openings On Back
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Headlight Shell & Rim
Custom Ready to Assemble Chrome Side Mount Headlight Bucket Rim & Retainer. Designed for 7" sealed or non sealed H4 type headlights. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Comes with a wired plug that works with sealed beam or H4 bulbs. H4 Beam Headlight sold separately #09-0072
Headlight Assembly
Chrome 7" Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. H4 Bulb with European style parking light (Not used for North American models)
Classic Round Black Taillight
Classic Round Black Taillight with plate bracket. 2 1/4" Round lens (with a clear bottom to light up your plates), 12 Volt double filament bulb. Works as a running and brake light.
Mini Bates Style LED Taillight ~ Chrome
Mini Bates Style LED Taillight ~ Chrome. 12 Volt taillight with 8 super bright LED's. Has running and brake light functions. Comes with mounting hardware and swivel bracket which allows it to be angled at different positions. Lens is 1 3/4" round, Outer bezel is 2 1/4" in diameter and is 2 1/4" long, Stands about 3" tall from base of mounting bracket. 3 Wire lead is about 12" long with bullet connectors. (Ground, running and brake light Wiring instructions) RED = Stop YELLOW = Running Lights BLACK = Ground
Mini Bates Style LED Taillight ~ Black
Mini Bates Style LED Taillight ~ Black. 12 Volt taillight with 8 super bright LED's. Has running and brake light functions. Comes with mounting hardware and swivel bracket which allows it to be angled at different positions. Lens is 1 3/4" round, Outer bezel is 2 1/4" in diameter and is 2 1/4" long, Stands about 3" tall from base of mounting bracket. 3 Wire lead is about 12" long with bullet connectors. (Ground, running and brake light Wiring instructions) RED = Stop YELLOW = Running Lights BLACK = Ground
Beehive Chrome Taillight
Beehive Chrome Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.
Beehive Black Taillight
Beehive Black Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.