Honda ► CX650C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CX650C►
- Honda
Cam Chain
Silent Cam Chain 417 x 78 OEM Ref # 14401-MA1-013 / 14401-MA1-003 / 14401-ME2-003 Made In Japan
Thermostat
Thermostat Unit, Replaces OEM # 19300-611-005
Water Pump Mechanical Seal
Waterpump Mechanical Seal OEM Ref # 19217-657-023 / 19217-611-000
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Side Stand Rubber
Side Stand Rubber Cushion. Replaces OEM # 50548-356-700
Brake Lever
Brake Lever OEM Ref # 53175-MA5-671 / 53175-MA6-016 / 53175-MA6-006
Clutch Lever
Clutch Lever - 10mm Bolt Hole OEM Ref # 53178-MA6-000
Front Brake Master Cylinder Repair Kit
Front Brake Master Cylinder Repair Kit OEM Ref # 45530-MA4-671
Front Master Cylinder Reservoir Diaphragm
Front Master Cylinder Reservoir Diaphragm. Replaces OEM # 45520-MA5-671 / 45520-MA5-672 / 45520-H5M-630
Ignition Spark Unit
Aftermarket Ignition Spark Unit for Honda - 2 units required per bike. Replaces Honda OKI or NEC units. Replaces OEM Ref # 30400-MA4-601
Oil Drain Plug
Magnetic Oil Drain Plug 14mm Diameter 1.5 Thread Pitch OEM Ref # 92800-14000 / 90101-14259-00
Petcock Repair Kit
Petcock Repair Kit
Air Cut Off Valve
Air Cut Off Valve OEM Ref # 16048-KB7-004
Carb Float
Carb Float with Pin, Replaces OEM # 16013-413-851 Note: Order the Quantity of Floats you Require
Carb Pump Diaphragm
Carb Pump Diaphragm OEM Ref # 16021-ME2-671 / 16021-MG1-671
Rectifier Regulator
Rectifier Regulator 2 Plugs (1 Three Prong with 3 Wires, One 6 Prong With 5 Wires) OEM Re f# 31600-MB1-008 / 31600-MJ8-671
Starter Clutch Repair Kit
Starter Clutch Repair Kit
Rick's Electrics ~ Alternator Stator
Rick's Electrics Brand OEM Style Alternator Stator - Installation Instructions Included.
Rick's Electrics ~ Starter Motor
Rick's Electrics Brand OEM Style Starter Motor Does Not Include the Starter Gear
Fork Seals
Fork Seals Set/2 39 X 52 X 11
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Front - Single
Brake Caliper Piston
Brake Caliper Piston - Front 32mm x 35mm OEM Ref # 43107-MA7-006
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 158.5mm Width: 40mm OEM Ref # 43120-415-000
Brake Pads
Front Brake Pads Pk/2 OEM Ref # 43105-MA3-007
Sintered Brake Pads
Front Brake Pads Pk/2 Sintered Pads OEM Ref # 43105-MA3-007
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-MG9-000
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22201-MG9-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Cylinder Head Intake Boot O-Rings (Set/4)
Cylinder Head Intake Boot O-Rings, Size 40 x 2.6 (Set of 4). Replaces OEM # 91301-371-005 / 91325-413-830 These are Used Where the Manifolds Attach to the Cylinder Heads.
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
OEM Type Shock Absorber Bolt
Chrome Shock Absorber Bolt, Replaces OEM # 93201-10032-0B Note: 2 Bolts Used Per Bike, Order the Quantity you Require
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Tachometer Cable
Tachometer Cable - Black - OEM # 37260-425-000 / 37260-ME8-000 / 37260-MA5-670 / 37260-ME-000 Made in Japan
Clymer Service Manual
Clymer Service Manual. Clymer motorcycle repair manuals are written specifically for the do-it-yourself enthusiast. From basic maintenance to troubleshooting to complete overhaul, Clymer manuals provide the information you need.
Haynes Workshop Manual
Haynes Workshop Manual. Feature clear step by step instructions covering the dismantling, inspection, repair and refitting of the engine, clutch and gearbox, cooling system, fuel and lubrication systems, ignition and exhaust systems, frame and fork, wheels, brakes and tires and the electrical system. Routine maintenance, complete specifications and detailed fault diagnosis procedures are also included.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. Replaces OEM # 45522-422-000
Handlebar Rubber Boot
Handlebar Rubber Boot. Replaces OEM # 53180-425-010
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Starter Clutch Roller Spring
Starter Clutch Roller Spring, Replaces OEM # 28125-516-030 Sold Each, Order the Quantity you Require
Water Temperature Sending Unit
Water Temperature Sending Unit, Replaces OEM # 37750-611-154
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Passenger Rear Footpeg Pin & Cotter Pin Set
Passenger Rear Footpeg Pin & Cotter Pin Set. Set Includes 2 Footpeg Pins and 2 Cotter Pins. Replaces OEM # 95015-83000
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.