Honda ► GL1000 ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1000 with universal parts included that match “honda sl125”►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 53165-390-780 / 53166-390-780 / 53166-422-000 / 53165-422-000
Honda OEM Type Grips ~ Open End
Honda OEM Type Rubber Grips - Black - Open End Type with End Plugs Included - For 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 53165-390-780 / 53166-390-780 / 53166-422-000 / 53165-422-000
Honda GL1000 Goldwing 1978-79 Replica Handlebar
Honda GL1000 Goldwing 1978-79 Replica Handlebar. Replaces OEM # 53100-431-780 / 53100-431-670 Thickness - 7/8" - 22mm, Length - 32 1/4" - 820mm, Pull Back - 7 3/4" - 196mm, Inner Rise - 9" - 228mm, End Rise - 10" - 254mm, Center Width - 6 1/2" - 165mm, Base Width - 10 1/2" - 266mm, Knurl Width - 4 1/2" - 114mm, Control Length - 9" - 228mm, Drilled NO There are Holes For Switch Positioning.
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-15001 Band Overall Size: 5.25" (133mm) Measuring from the inside of the brackets.
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal. This internal rubber seal replaces the ripped, dried or missing rubber internal seal. This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Side Cover Emblem
Cast Metal Side Cover Emblem with Attachment Clips. Replaces OEM # 87130-431-670 This is a Stock Type Replacement Emblem for the Honda GL1000K 1977-79 - Some 1977's used decals instead of emblems. Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Seat Cover GL1000 1978-79
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Complete installation instructions as well as step by step instructions on how to repair damaged seat foam can be found in the instructions section of our website. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
GL1000 1978-79 Warning and Service Label Set
Honda GL1000 1978-79 Goldwing ~ Warning & Service Label (Sticker) Set. This set includes several warning and service labels that were originally found on these bikes when new. You'll find the quality & accuracy of these decals second to none and accurate in every detail. These reproductions will add the finishing touch to your restoration. This set includes "Preserve Nature" decals in both Black and White which makes this set correct for a GL1000 1978-79 of any colour. This 9 piece warning & service label set includes: 1 Important Information (tire info) 1 Accessories & Loading: Warning 1 Caution: Radiator Warning 1 Danger: Fan Warning 2 Helmet Holder 1 Exhaust Modification Warning 1 Remember: Preserve Nature (helmet warning) - Black printed on clear 1 Remember: Preserve Nature (helmet warning) - White printed on clear 1 Reserve Tank: Coolant Level - Printed on white These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Exhaust Valve
Exhaust Valve OEM Ref # 14721-371-000 / 14721-371-405 Made In Japan
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Rear - Single
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat 1.0, Main Jet #60, Main Jet #120, Secondary Jets #60, 120, 130 and 140, Needle Jet, Low Speed Jet #38, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Packing, 2X Springs, 2X Metal Washers, Nut, Rubber Plug and 5 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Standard Carb Rebuild Kit
Standard Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat, Secondary Jets #60, 130 and 140, Needle Jet, Low Speed Jet #35, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Packing, Spring and 5 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Horn Sub Harness
Horn Sub Harness, This is the Harness that Attaches to the Horns. Replaces OEM # 32103-431-000
GL1000K 1978-79 Complete Decal Set
GL1000K 1978-79 Complete 8 Pc. Decal (Sticker) Set. Includes - RH upper shelter cover stripe, LH upper shelter cover stripe, RH lower shelter cover stripe, LH lower shelter cover stripe, RH side panel stripe, LH side panel stripe, RH radiator cover stripe and LH radiator cover stripe. These reproductions will add the finishing touch to your restoration. These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Passenger Floorboard Set
Complete Passenger Floorboard Set Includes All Mounting Hardware
Intake Valve
Intake Valve OEM Ref # 14711-371-000 Made In Japan
Rear Fender Bolt Set
Rear Fender Bolt Set of 2, Replaces OEM# 90102-371-000 These are the large main bolts that go in the middle portion of the rear fender. The grab bar bolts thread into these fender bolts.
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Rear Brake Master Cylinder Repair Kit
Rear Brake Master Cylinder Repair Kit OEM Ref # 43530-410-305
Front Brake Stop Switch Assembly
Front Brake Stop Switch Assembly, Replaces OEM# 35340-413-013
Master Cylinder Reservoir Kit
Master Cylinder Reservoir Kit - Front
Brake Pads
Front Brake Pads Pk/2 OEM Ref # 45105-438-007
Front Brake Caliper Bolt Set
Front Brake Caliper Bolt Set, Replaces OEM# 90123-371-000. Each set includes 2 bolts and 2 washers - enough for either the left or right caliper. If you would like bolts for both sides purchase 2 sets.
Primary Chain
Primary Chain - 60 Link OEM Ref # 23131-371-004 Made In Japan
Engine Oil Seal Kit
Engine Oil Seal Kit - 11 Pc Kit Kit includes: Cylinder Head Seals (3 Pieces), Tachometer Seal, Oil Pump Seal, Clutch Cover Seal, Cover RR Seals (2 Pieces), Cylinder Block Seal, Crankshaft Seal and Oil Pump Seal.
Radiator Fan Cooling Switch O-Ring
Radiator Fan Cooling Switch O-Ring, Replaces OEM# 91307-PH9-000
Thermostat Cover O-Ring
Thermostat Cover O-Ring - 54 x 2 Size - Replaces OEM# 91307-MB0-003 / 91307-MB0-000 / 91302-317-700
Dynatek Dyna S Ignition System (Ultimate Kit)
Dynatek Dyna S Ignition System (Ultimate Kit) with 2X Dynatek Brand Performance 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System (Premium Kit)
Dynatek Dyna S Ignition System (Premium Kit) with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. Includes instructions and comes with a one year warranty through Dynatek.
Dynatek Dyna S Ignition System
Dynatek Dyna S Ignition System. The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines. The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA. This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.
Front Master Cylinder Reservoir Diaphragm
Front Master Cylinder Reservoir Diaphragm. Replaces OEM # 45520-371-003 / 44520-371-013
Electronic Ignition System
Electronic Ignition System. Direct plug-in fitment. Increase RPM 100% tested before shipment, high reliability and high performance!
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-292-003 / 30203-292-154
Muffler Joint Gasket
Muffler Joint Gasket 43mm x 48.5mm x 20mm OEM Ref # 18392-413-000 / 18392-MG7-750 Fits: CrossOver
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850949
Complete Gasket Set
Brand New complete gasket set. Sealed Complete (Top + Bottom End). The Gaskets come with Silicone Line Coatings, Non Asbestos, Special Chemical & Mixture have been treated to the Gasket materials in order to withstand high Pressure oil resistance. All gaskets needed to do a complete overhaul on the engine. Includes all items pictured.
Top End Engine Gasket Set
Brand New Top End Gasket Set. The Gaskets come with Silicone Line Coatings, Non Asbestos, Special Chemical & Mixture have been treated to the Gasket materials in order to withstand high Pressure oil resistance. Includes all items pictured. ISO 9001 Standards.
Float Bowl Gasket
Float Bowl Gasket
Fork Seals
Fork Seals Set/2 37 X 48 X 12.5
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Brake Pedal Pin
Brake Pedal Pin, Replaces OEM# 46503-371-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Cylinder Head Emblem
Cylinder Head Emblem with Attachment Clips, Replaces OEM# 12312-371-610 / 12312-371-611
Final Gear Cover Gasket
Final Gear Cover Gasket - Replaces OEM# 11372-463-003 / 11372-463-306 / 11372-371-010 / 11372-371-306 / 11372-371-000
Clutch Oil Pump Gasket
Clutch Oil Pump Gasket - Replaces OEM# 15229-371-000