Honda ► GL1100I ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1100I►
- Honda
Press In Type Pilot Jet Set ~ Size #38 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #38) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #38 which is oversize for these bikes, please confirm this is the size you require before purchasing.
Press In Type Pilot Jet Set ~ Size #42 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #42) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #42 which is the oversize for these bikes, please confirm this is the size you require before purchasing.
Oil Tube Plug
Oil Tube Plug, Replaces OEM # 15337-300-010
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Carb Bolt Kit
Carburetor Bolt and Washer 35 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-551-020 Sold Each, Order the Quantity you Require.
Side Cover Emblem
Side Cover Emblem, Replaces OEM# 83605-MG9-000 / 83605-MG9-010 / 83605-463-000 / 83605-463-505 Sold Each, Order the Quantity you Require
Clutch Cover Hardware Set
Clutch Cover Hardware Set. Set includes the 6 Bolts and 2 Nuts Used to Fasten the Clutch Cover. Includes 4X 95801-0608500 , 2X 95801-0603500 , 2X 94050-06000
Chrome Timing Belt Cover Set
Chrome Timing Belt Cover Set, Replaces OEM# 11511-371-010 / 11521-371-010. Spruce up your bike with a new set of chrome covers. These new covers really make these bikes look amazing!
Air Chamber Gasket
Air Chamber / Plenum Gasket, Replaces OEM# 16075-463-004 Fix those unseen air leaks with this gasket.
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Front Brake Caliper Bolt Set
Front Brake Caliper Bolt Set, Replaces OEM# 90123-371-000. Each set includes 2 bolts and 2 washers - enough for either the left or right caliper. If you would like bolts for both sides purchase 2 sets.
Fuel Tank Rubber "C"
Fuel Tank Rubber "C" - Replaces OEM# 17616-371-000 This rubber is used with the stock bolt and collar to attach through the hole near the top of the fuel tank.
Oil Pump Rebuild Kit
Oil Pump Rebuild Kit Each Kit Contains: Each Kit Contains 91207-580-015 (Oil Seal 10x25x7) x1, 91208-MN1-771 (O-Ring 11x15x3) x1, 91302-200-000 (O-Ring 33.5x3) x1, 94201-30450 (Split Pin 3.0 x45) x1, 15128-371-000 (Oil Passage Gasket) x1, 15229-371-000 (Clutch Oil Pump Gasket) x1.
Fuel Petcock Assembly
Fuel Petcock (Gas Tap) Assembly with Port O-Rings, Replaces OEM# 16950-371-025 / 16950-MG9-005 This petcock has a "reserve" function that did not appear on the original GL1200 petcock. Outside diameter of port is 6 mm and inside diameter is 4mm