Honda ► SL350 ►
-
Here’s our hand-picked list of parts and accessories for your Honda SL350►
- Honda

Sidecover Damper Rubber A
Rubber Sidecover Damper A, Replaces OEM # 17247-303-000

Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires

Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008

Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000

Cam Shaft Roller Collar
Cam Shaft Roller Collar - Replaces OEM # 14606-286-000

Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.

Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670

Brake Lever
Brake Lever OEM Ref # 53175-402-700 / 53170-216-670 / 53175-286-000 / 53170-286-670 / 53170-329-010 / 53170-369-700 / 53175-369-700

Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!

Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671

Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671

Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154

Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154

Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require

Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-286-000 / 18291-286-306

Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.

Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850353 Please note Oil Pump Gasket Not Included

Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17525-300-000

Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310

Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's

Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.

Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.

Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000

Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.

Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000

Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require

Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike

Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers

Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-287-004

Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004

Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require

Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require

Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require

Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.

Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.

Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan

Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-149-000 (700mm), 37260-KB7-010 / 37250-149-000 Made in Japan

Tachometer Cable
Tachometer Cable - Black - OEM # 37260-425-000 / 37260-ME8-000 / 37260-MA5-670 / 37260-ME-000 Made in Japan

Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000

Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000

Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001