Honda ► SL350 ►
-
Here’s our hand-picked list of electrical parts for your Honda SL350 with universal parts included that match “honda sl125”►
- Honda
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Bar Switch Assembly - Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side. Replaces OEM # 35300-319-670
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Performance Starter Motor
Rick's Electrics Brand Performance Hot Shot Starter Motor Unit, Replaces OEM# # 31200-286-405 / 31200-286-168 / 31200-286-158. It is an upgraded 4 brush permanent magnet starter; it includes a new cable that is longer than the stock piece for easy installation.
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Charging Kit
Rick's Electrics Charging Kit for use with Standard Lead Acid Batteries. Kit includes both a high quality stator and a rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.