Honda ► SL350 ►
-
Here’s our hand-picked list of parts and accessories for your Honda SL350 with universal parts included that match “honda sl125”►
- Honda
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Clutch Lever Perch
Clutch Lever Perch, Replaces OEM# 53172-310-010 / 53172-110-000 / 53172-310-000 Includes a 10mm Mirror Mount, for 7/8" handlebars
Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670
Brake Lever
Brake Lever OEM Ref # 53175-402-700 / 53170-216-670 / 53175-286-000 / 53170-286-670 / 53170-329-010 / 53170-369-700 / 53175-369-700
Brake Lever Perch
Brake Lever Perch, Replaces OEM# 53171-312-003 Includes a RH Thread 10mm Mirror Mount. Fits to 7/8" handlebars and includes a hole for the brake light switch.
Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref # 37260-KB7-010 / 37260-438-000 Made in Japan Length is 24" - Confirm this is the length you require before purchasing
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 40543-471-000 / 40543-312-010. If you require 2 adjusters purchase 2 of this part.
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-286-000 / 18291-286-306
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-149-000 (700mm), 37260-KB7-010 / 37250-149-000 Made in Japan
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-286-000
Cam Shaft Roller Collar
Cam Shaft Roller Collar - Replaces OEM # 14606-286-000
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Fork Dust Seals
Fork Dust Seals Set/2 35 X 53 OEM Ref # 91254-434-003 / 91254-435-003 / 51425-340-000
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM# 17613-286-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Honda Handlebar Pad
Honda Handlebar Pad Protect your chest and spruce up the look of your bike with a brand new handlebar pad. These will fit to 1/8" and 7/8" bars.
Honda Tin Sign
Honda Tin Sign Spruce up your garage or man cave with this 12" by 12" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo Flag
Honda Logo Flag - Features the classic Honda logo, measures 36" by 23" and includes metal stud holes in each corner for easy mounting. Will look great in any garage or shop!
Honda Beanie Hat / Toque
Honda Beanie Hat / Toque. This black beanie features the classic Honda Logo on both sides. This hat is one size fits all but does fit quite large.
Honda Garage - Tin Sign
Honda Garage with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.