Honda ► XL250R ►
-
Here’s our hand-picked list of electrical parts for your Honda XL250R with universal parts included►
- Honda
Tail Light Lens
Tail Light Lens, Replaces OEM# 33702-MC4-671 / 33702-MGR-305
Tail Light Assembly
Tail Light Assembly, Replaces OEM# 33701-KB7-003 / 33701-MC4-671 / 33701-GAN-671 This Tail Light Does Not Have Reflectors on the Sides of the Lens. 102mm center to center of the rear thread in holes.
Tail Light Lens
Tail Light Lens, Replaces OEM# 33702-MC4-671 / 33702-KB7-003 / 33702-KB7-013 / 33702-MGR-305 / 33702-GF4-000 / 33702-MG2-942 This Tail Light Does Not Have Reflectors on the Sides of the Lens.
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front OEM Ref # 33402-428-672
Turn Signal Lamp
Turn Signal Lamp - Black Left Front Single Filament - 12 Volt OEM Ref # 33350-MG2-671
Turn Signal Lamp
Turn Signal Lamp - Black Right Front Single Filament - 12 Volt OEM Ref # 33300-MG2-671
Ignition Switch
Ignition Switch w Keys, Replaces OEM# 35100-KB7-017 Plug and play fit for the models listed.
Rectifier Regulator
Rectifier Regulator - Replaces OEM# 31400-KA2-641 / 31400-KB7-008 / 31400-MK2-681 Easy to install, just plug and play. Includes fins for improved cooling. Input Voltage: DC 12V
Regulator Rectifier
Regulator Rectifier, Replaces OEM# 31600-KG0-000 / 31600-MC4-000 Easy to install, just plug and play. Features fins for improved cooling. Input Voltage: DC 12V
Rick's Electrics High Performance Stator
Rick's Electrics High Performance Stator, Replaces OEM# 31120-KL4-771 / 31120-KL4-772 / 31120-KR6-003 / 31120-KR6-004 This higher output stator will provide additional wattage for electrical power.
Ignition Coil with Cap
Ignition Coil with Cap, Replaces OEM# 30500-VM3-405 / 30510-167-003 / 30500-187-000 / 30500-167-013 / 30500-187-010 / 30500-167-003 / 30500-196-600 / 30500-GC1-000 / 30501-958-000.
Spark Plug Ignition Coil Cap Boot
Spark Plug Ignition Coil Cap Boot, Replaces OEM# 30700-MA0-163 / 30700-MC4-153 / 30700-MA0-153 / 30700-KA2-003 / 30700-HM5-630 / 30700-965-003 / 30700-965-013. Angle = 120 Degrees Height = 40mm or 1.57" Length = 59mm or 2.23" Resistor = 5k OHM
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Alternator Stator
Alternator Stator, Replaces OEM# 31120-KR6-004 / 31120-KR6-415 / 31120-KL4-771 / 31120-KL4-772 Direct replacement to your original unit (plug and play). Highest grade materials, resistant to 200 degrees Celsius. Each unit has been tested to ensure great quality!
Ignition Coil with CDI Box
Ignition Coil with CDI Box, replaces OEM# 30510-GR2-405 / 30510-KG0-003 Double check the CDI plugs match your bikes before purchase.
Headlight Lens Insert
Headlight Lens Insert, Replaces OEM# 33100-KL4-611 / 33100-KL4-671 / 33100-KL4-670
Rear Turn Signal
Rear Turn Signal, Replaces OEM# 33500-KL3-671 / 33500-KL3-672 / 33550-KL3-671 / 33550-KL3-672 / 33500-MG2-672 / 33500-KL4-670 / 33550-KL4-670 / 33500-MM9-720 / 33550-MM9-720 / 33500-KVO-670 / 33550-KVO-670 / 33500-KW3-770 / 33550-KW3-770
Rear Turn Signal
Rear Turn Signal, Replaces OEM# 33500-MC4-671 / 33550-MC4-671
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.