Honda ► CB360K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB360K►
- Honda
Gas/Fuel Tank Cap Latch Assembly ~ Black
Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch with Return Spring, Latch Mounting Pin and C-Clip.
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Stock Type Reflector
Stock Type Screw on Reflector, Replaces OEM # 33741-340-670
Rear Signal Lamp Stay
Rear Signal Lamp Stay - Chrome Rear type - OEM Ref # 33441-369-000 125mm Long.
Front Stop Switch
Front Stop Switch & Safety Starter Switch OEM Ref # 35340-329-003 / 35340-102-003 / 35340-401-682 / 35340-329-000 / 35340-086-721
Custom Triple Tree Steel Nut ~ Joker Machine
Joker Machine Brand ~ Custom Triple Tree Steel Nut, Replaces OEM # 53220-286-000 High quality CNC machined part made in the U.S.A.
Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.
Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 52108-457-300 Note: These Replace the factory plastic OEM Type Bushings.
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Master Cylinder Reservoir Cap Plastic O-Ring
Master Cylinder Reservoir Cap Plastic O-Ring, Replaces OEM # 45521-MJ6-006
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 45110-300-003 / 45224-579-013
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-369-004
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Brake Hose Rubber Grommet
Brake Hose Rubber Grommet, This is the Rubber Grommet that Attaches to the Brake Hose. Replaces OEM # 45146-300-000
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Front Stop Switch Sub Harness
Front Stop/Brake Switch Sub Harness, Replaces OEM # 35345-319-000
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
Fork Dust Boot Set
Fork Seal Dust Boots (Set/2). 33mm Size, Replaces OEM # 91254-413-881
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Master Cylinder Damper Set
Master Cylinder Damper Set. Includes Brake Master Cylinder Rubber Damper, Plate and Washer. This Set is often missing and is used to reduce vibration to the master cylinder lever.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Throttle Adjusting Spring
Throttle Adjusting Spring, Replaces OEM # 53191-300-000
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Valve Guide Clip
Valve Guide Clip, Replaces OEM # 12211-250-310 Sold Each, Order the Quantity you Require
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Front Brake Caliper Bolt & Washer Set
Front Brake Caliper Bolt & Washer Set. Set includes 2 Bolts and 2 Washers. Replaces OEM # 90165-323-000
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Cap (Set/2). These Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-362-000 X2.
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Custom Drive Chain Adjuster Screws ~ Silver ~ Joker Machine
Joker Machine Brand ~ Silver Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. Body Length 26mm, Thread 21mm, Total Length 47mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)